Easy-Lock Pet Gate
Instruction Manual
Thank you for choosing Richell’s Easy-Lock Pet Gate. Please read this instruction manual carefully before
assembling or using this product, and keep for future reference.
Note
l
Do not use the product for anything other than its intended purpose.
l
Injury or death to pet may be caused if pet behaves unexpectedly if startled by thunder and lightning,
or other animals. Keep the product in a place where it remains in sight, and keep it open when unattended.
l
Take caution not to stumble when stepping over the bottom of frame.
l
Do not place the product at the top of staircase or near a glass door.
l
Lock the Gate Door to keep pets properly confined (Fig. 8).
l
Be sure to place the product against walls with a width of 2.4" (6 cm) and above, and on a flat sturdy surface
(Fig. 7).
l
This product fits openings from 28.3-35.4"(72 to 90 cm). Do not place the product outside this range (Fig. 6).
l
Keep the product away from fire or extremely high temperatures.
l
Do not use a leash with your pet when using this product. Pet could become tangled.
l
Do not lean or sit on the product.
l
Tighten Adjuster Knob at the space between Main Frame and Lower Gate Lock to 0.08-0.12"(2-3 mm)
so that the tension spring effect works properly (Fig. 4).
l
Tighten Adjuster Knob at the space between Main Frame of Upper Gate Lock to 0.04-0.08"(1-2 mm) so that
the tension spring effect works properly (Fig. 5).
l
Be careful of sharp objects while assembling.
l
Make sure the Gate Door is locked when it is closed.
l
Place the product against sturdy wall surfaces (locate studs) to prevent damage to the wall surface.
l
Use the product carefully. Do not drop or hit it.
l
Be sure the product is securely fixed. If not, tighten Adjuster Knobs as necessary (Fig. 7).
l
Do not try to force the Gate Door open past 90 degree angle.
1.8” (4.5 cm) and under
1.8” (4.5 cm) and under
Lower Gate Lock
Upper Gate Lock
This product is designed for small and medium dogs, 8.8-44 lbs. (4-20 kg). No screws or additional tools are
needed to mount the product in a doorway or hallway opening with width of 28.3-35.4" (72-90 cm).
Examples of dog types (8.8-44 Ibs./4-20 kg)
Do not use with pets exceeding 44 Ibs (20 kg)
Small dogs
Medium dogs
Terrier, Dachshund, Chihuahua
Beagle, Schnauzer, Spaniel
Designed for placing against the wall or within
the door frame using the tension spring effect.
Before installing, the top width of frame will be wider than the
bottom because the product is designed to be mounted using
the tension spring effect. Tighten the top Adjuster Knob to create
the same spacing between the Gate Door and the Main Frame.
Side Frame can be adjusted to keep pet confined.
When closed, the Gate Door is locked automatically.
Adjust the clearance using the Side Frame to keep pets properly
confined.
Side Frame
lock
lock
If too much or too little force is used when closing, the Gate Door may not lock.
l
Be sure the Gate Door is locked (at bottom and top) when it is closed.
l
If the Gate Door is pushed too hard when closing, it may overpass the
Gate Lock and cause damage to Upper/Lower Gate Locks and wooden
parts.
Before assembling, be sure all parts are included, as shown.
Gate Door
Main Frame
Body
Side Frame (2)
Long Adjuster Bolt
(4)
Short Adjuster Bolt
Adjuster Knob
Hexagonal Nut
4 Sets
Short Adjuster Bolt (1)
Adjuster Knob (1)
Hexagonal Nut (2)
Adjuster set (packed)
l
Decide which of the optional parts will be used to assemble the product.
l
Parts needed will vary, depending on your doorway/hallway
opening, as shown below. Keep parts away from children.
l
To attach the product in opening with width of 30.7-35.4"(78-90 cm),
use the Side Frame. Adjust Hexagonal Nuts until the clearance
between each Frame is set to 1.8” (4.5 cm) and under as shown.
l
Tighten Hexagonal Nuts after adjusting the clearance.
Type A
Type B
Insert Adjuster Knob through Short Adjuster Bolt.
Attach Hexagonal Nut, Side Frame, another Hexagonal
Nut, and Adjuster Knob to Long Adjuster Bolt, in this order.
Adjuster Knob
Adjuster Knob
Short Adjuster Bolt
Long Adjuster Bolt
Hexagonal Nut
Side Frame
1.8" (4.5 cm) and under
1.8" (4.5 cm) and under
Side Frame
Hexagonal Nuts
Required Parts
Body
Long Adjuster Bolt
Adjuster Knob
Side Frame
Hexagonal Nuts
(1)
(4)
(4)
(2)
(8)
Cautions
4 .
Examples of assembly
Insert
Insert
Insert
Insert
Insert
Insert
Insert
Insert
Insert
Insert
Insert
Insert
Set the desired width while tightening Upper Adjuster Knob.
●
For opening widths
28.3-30.7
"
(72-78 cm)
●
For opening widths
30.7-33.1
"
(78-84 cm)
●
For opening widths
33.1-35.4
"
(84-90 cm)
Required Parts
Body
Short Adjuster Bolt
Adjuster Knob
(1)
(4)
(4)
Body
Short Adjuster Bolt
Long Adjuster Bolt
Adjuster Knob
Side Frame
Hexagonal Nuts
(1)
(2)
(2)
(4)
(1)
(4)
Required Parts
Examples of assembly
6 .
Parts/Specifications
3 .
Features
2 .
Usage
1 .
Product Applictions
1 .
Before assembling
5 .
1
2
Type A
Type A
Type A
Type A
Type B
Type A
Type A
Type B
Type B
Type B
Type B
