Rice Lake 482-AG Скачать руководство пользователя страница 33

Страница: 33 / 60

Configuration

© Rice Lake Weighing Systems

●

COM-1 Parameters

COM-2 Parameters

Parameter

Settings

Description

TRIGER

(

COM-1

)

—

The trigger parameter specifies the ports mechanism for triggering a transmission of data

DEMAND

When set to a demand port, printing is performed by pressing the

PRINT

key or when a KPRINT EDP command is

received; this port also allows operation and EDP commands

PRN

When set to a printer port, printing is performed by pressing the

PRINT

key; the port does not allow operation of

EDP commands

NONE

When set to

NONE

, the port is inactive

COMAND

When set to a command port, the port allows operation of EDP commands, but will not print

BAUD

9600

19200

38400

1200

2400

4800

The baud rate setting determines the transmission speed of data

BITS

8NONE

7EVEN

7ODD

The bits parameter determines the number of data bits and parity of data

SBITS

1 STOP

2 STOP

The stop bits parameter sets the number of stop bits to 1 or 2

TERMIN

CR/LF

The termination character parameter sets the line termination character(s) for data sent

EOLDLY

000

0 – 255

The end-of-line delay parameter specifies, in 0.1 second intervals, the delay between transmitted lines of data

NOTE: An end-of-line delay may be required for continuous transmission at slower baud rates to ensure

the receiving buffer is empty before another string is transmitted.

ECHO

OFF

The echo parameter specifies whether characters received by the port are echoed back to the sending unit

PRNMSG

OFF

The print message parameter determines if

Print

displays when a demand print is performed

Table 3-12. COM1 Parameters

Parameter Settings

Description

TRIGER

(COM-2)

—

The trigger parameter specifies the ports mechanism for triggering a transmission of data

NONE

When set to

NONE

, the port is inactive

PRN

When set to a printer port, printing is performed by pressing the

PRINT

key; the port does not allow operation of EDP

commands

STR1

When set to

STR1

the port is used to transmit a continuous stream of data according to RLWS stream format**

STR2

When set to

STR2

the port is used to transmit a continuous stream of data according to Toledo8142 stream format**

STR3

When set to

STR3

the port is used to transmit a continuous stream of data according to Cardinal738 stream format**

STR4

When set to

STR4

the port is used to transmit a continuous stream of data according to Weightronix WI-120 stream format**

STR5

When set to

STR5

the port is used to transmit a continuous stream of data according to consolidated controls stream format**

**STREAM must be set to local to enable streaming

NOTE: See

Section 3.6.3 on page 31

for more information on Stream formats.

Com-2 streams simultaneously on both the RS-232 and 20mA outputs, see

Figure 2-6 on page 10

BAUD

9600

19200

38400

1200

2400

4800

The baud rate setting determines the transmission speed of data

Table 3-13. COM2 Parameters

Содержание 482-AG





























































Результаты поиска

Содержание 482-AG

Отзывы:

Бренды по названию

Популярные бренды

Rice Lake 482-AG, Техническое руководство

Результаты поиска

Содержание 482-AG

Отзывы:

Бренды по названию

Популярные бренды