manualshive.com logo in svg

Rice Lake 482-AG, Техническое руководство

Поделиться
Скачать
Rice Lake 482-AG Скачать руководство пользователя страница 35

Configuration

© Rice Lake Weighing Systems

 

●

 All Rights Reserved

31

3.6.3 Continuous Data (Stream) Output Formats

When the trigger setting for COM-2 is set to one of the stream formats (STR1-STR5), or the Ethernet client or server trigger 

setting is STRLFT or STRIND, data is continuously streamed from the appropriate port in one of the five fixed formats that 

follow.

Rice Lake Stream Data Format

Figure 3-10. STR-1 Rice Lake Stream Data Format

<STX>         <POL>        <wwwwwww>            <UNIT>        <G/N>     <S>       <TERM>

ASCII 02
decimal

Polarity:
<space> = Positive
<–> = Negative

Weight: 7 digits, right-justified, dummy
zeroes, decimal point with no leading
zeroes except for leading zero immediately
preceding the decimal point. Leading
zeroes transmitted as spaces.

L = pounds
K = kilograms
T = tons
G = grams
O = ounces

G = Gross
N = Net

Status:
<space> = valid
I = Invalid
M = Motion
O = Over/under range
Z = COZ

<CR> <LF>
or <CR>

Содержание 482-AG





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды