background image

II�FullSizeCanisterTroubleshootingGuide

07�03�07

11

F. Power Nozzle w/ Dirt Sensor Will Not Run But Canister Runs

F�

Step 1.

Checkthehosetoseeifthelightindicatesthatthenozzleison�

F�

Step 2.

Checkthenozzletoseeifthesensor/indicatorlightis“ON”,andifonwhatcolorisit�
LightisOFF:

Go to 

page 10, D. Canister Runs, Power Nozzle Does Not Run

LightisRED:

Go to Step 3.

LightisGREEN:

Go to Step 4.

LightisORANGE:

Go to Step 5.

NOTE:Ifthemotorisnotrunningtherewillbenoheadlight�

F�

Step 3.

Pushtheresetswitch/breaker(SeeFigure

B. Power Nozzle Reset Switch Location

)�

Turnthepowernozzle“ON”�

Does the nozzle start, the indicator light turn GREEN, and the headlight come on?

YES: Checktheheightadjustmenttoensureitissettoproperheightforthetypeofcarpetbeingvacuumed�

NO: Ifbreakercontinuestotrip,thebreakermaybeweakandshouldbereplaced�
NOTE:IflightisREDandpowernozzleruns-Checkwiring(SeeFigureL�WiringDiagramForDirtSensorModels)�

F�

Step 4.

Turnthecanisterandpowernozzle“ON”;pushthenozzlethroughsomedirtandseeifthelightturnsORANGE�
LightturnsORANGE: Sensorisworkingandbreaker/resetswitchisgood�

Removenozzleandcoverandcheckthemotorandwiringtothemotor�

LightstaysGREEN: Removenozzleandcoverandcheckthemotorandwiringtothemotorandthatthesensorsareinplace�

Checkmovementofwiringwhenhandleismovedupanddown�Ifsensormoves,removesensorleads

fromziptie�

F�

Step 5.

ORANGElightnormallyindicatesthatdirthasbeenfound�
IflightstaysORANGEitindicatesthatthesensorhasdirtormoistureonthesensorlenslocatedoneoneachsideoftheinlet

duct�

Clean lens by first removing the base plate and brush roll.  Using a paper towel, reach up and wipe the dirt/moisture from the 

lens�

Aftercleaning,thelightshouldchangetoGREEN�

NOTE:

IftheindicatorlightisORANGEandmotorisnotrunning,checkthemotorandwiringtothemotor�

Figure C. Power Nozzle Warning Light & Dirt Sensor Location

Dirt Sensor / Warning Light

Содержание 1700























Отзывы: