background image

[11] 

 

d.

 

Your tool is equipped with a single work 
light (9).  The work light will be activated 
when the trigger switch is squeezed.  

e.

 

Your tool is equipped with a Motor 
Control switch (10).  This switch locks the 
trigger while in the center position and 
permits motor drive when to the left. 

WARNING

: Work light is for providing 

light to the immediate work surface and is 
not intended to be used as a flashlight. 
f.

 

Your tool is equipped with three cutting 
blades, one dynamic (1) and two 
stationary or static (2).  The middle blade 
reciprocates up and down between the 
two static blades to cut the glass. 

g.

 

To remove the battery (7), from the 
handle (6) of the tool, press both 
unlocking buttons and firmly pull the 
battery outward from the handle. 

h.

 

Align the battery pack with the rails of the 
tool’s handle and slide it firmly into the 
handle until you hear the lock snap into 
place. 

WARNING

SHEAR HAZARD.  ALWAYS 

keep hands, fingers, hair, clothing and/or 
other body parts clear and away from 
between or near cutting blades.  Severe 
injury will result. 

i.

 

 

WARNING

SHEAR HAZARD. To reduce 

the risk of serious personal injury, 
disconnect the battery pack before making 
any adjustments, maintenance or 
removing/installing attachments or 
accessories.

 

2) CUTTING LAMINATED GLASS 

a.

 

Don personal protective equipment 
including ANSI approved safety 
goggles, respirator and cut-resistant 
gloves. 

b.

 

Place suction lifters on laminated glass 
to be cut and activate the suction by 
lifting the movable handle. 

c.

 

Grasp tool handle with the right hand 
with a pistol grip and place left hand 
along motor housing. 

d.

 

Many newer vehicles have glass 
configurations which increase the 
energy required to make purchase 
into the windshield glass.  When 
attempting to make purchase, 2 
methods are recommended 1) impact 
with a halligan bar and 2) impact with 
the cutter blade tips.   

e.

 

Make purchase with the halligan bar in 
the desired location to begin cutting. 

 

 

f.

 

If the tool blade tips are to be used, 
impact the glass moderately at a 90° 
angle or perpendicular.  If after 2-3 
impacts have not breeched the glass, 
stop immediately.  (NOTE: The 
operator can get a “feel” when the 
glass is very tough after only 2-3 
impacts). 

 

g.

 

If the glass in that location is curved 
significantly or is very close to the 
edge near support like the A-pillar, 
move your purchase point to a new 
location which is flat or near flat and 
try 2-3 more impacts. 

h.

 

If this further fails to make purchase, 
stop and use the mini halligan bar 
provided with the tool set to make 
purchase. 

Содержание RHYNO2

















Отзывы: