Rheem Solar Thermosiphon Water Heater Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 64

Rheem Solar Thermosiphon Water Heater Скачать руководство пользователя страница 16

16

SAVE A SERVICE CALL

Check the items below before making a service call. You will be charged for attending to any condition or
fault that is not related to manufacture or failure of a part.

NOT ENOUGH HOT WATER (OR NO HOT WATER)

This can occur with new installations and is normally related to some misunderstandings as to the use of the
booster heating unit.

Insufficient sunlight

Insufficient sunlight due to cloudy weather during hotter months or
low solar energy contribution in colder months may mean the
booster heating unit is required to boost more often.

Ensure the booster heating unit is being used as advised. Refer to

“Booster Control”

on page 7.

Booster heating unit not operating

Inspect the isolating switch marked “HOT WATER” or “WATER
HEATER” at the switchboard and ensure it is turned “ON”.

Check the timer (if one is installed) and its settings to ensure power
is available to the booster heating unit.

Note:

Check the electricity supply to which the unit is connected. If on an Off-Peak or time controlled

electricity supply remember heating hours are restricted.

Check the fuse marked “HOT WATER” or “WATER HEATER” at the switchboard.

Collectors shaded

If trees or other objects shade the solar collectors or if the glass is dirty, the effectiveness of the solar
collectors will be greatly reduced. Have the trees trimmed or the solar collectors relocated if the
obstruction is permanent or clean the collector glass (refer to

“Collector Glass”

on page 12).

Are you using more hot water than you think?

Is one outlet (especially the shower) using more hot water than you think?

Very often it is not realised the amount of hot water used, particularly when showering. Carefully review
the family‟s hot water usage. As you have installed an energy saving appliance, energy saving should
also be practised in the home. Adjust your water usage pattern to take advantage of maximum solar
gains.

Have your plumber install a flow control valve to each shower outlet to reduce water usage.

Temperature pressure relief valve running

Is the relief valve discharging too much water?

Refer to

“Temperature Pressure Relief Valve Running”

on page 17.

Thermostat setting

Ensure the thermostat setting is appropriate. You may choose to have your electrician adjust the
thermostat upwards to gain additional hot water capacity when boosting.

Refer to

“Temperature Adjustment”

on page 6.

Warning:

Hotter water increases the risk of scald injury.

Water heater size

Do you have the correct size water heater for your requirements?

The sizing guides in the sales literature and on the Rheem website

(www.rheem.com.au)

suggest

average sizes that may be needed.

«
...
14
15
16
17
18
...
»

Содержание Solar Thermosiphon Water Heater

































































Отзывы:

Нет отзывов