Rheem Solar Loline Conversion Kit Electric Water Heater Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 40

background image

ABOUT YOUR WATER HEATER

6

·
·

TO TURN ON THE WATER HEATER

·

Open the cold water isolation valve fully at the inlet to the water heater.

·

If the solar collectors and solar hot and cold pipes have been drained, it will be
necessary to bleed the collector circuit (refer to “Bleeding the Solar Collectors”
on page 7).

If the electrical supply to the water heater has been switched off:

Switch on the electrical supply to the solar storage tank at the isolating switch

Switch on the electrical supply to the solar control unit at the power outlet.

HOW DO I KNOW IF THE WATER HEATER IS INSTALLED CORRECTLY?

Installation requirements are shown on pages 23 and 26. The water heater must be
installed by an authorised person and the installation must comply with national
codes AS/NZS 3500.4.2, AS/NZS 3000, and all local codes and regulatory authority
requirements. In New Zealand, the installation must conform with the New Zealand
Building Code.

Note:

The solar hot and cold pipe work between the solar storage tank and the

solar collectors

must be

of copper and fully insulated with Armaflex insulation or

similar (minimum thickness 10 mm). The insulation must be weatherproof if
exposed and fitted up to the connections on the storage tank, as very high
temperature water can flow from the solar collectors to the storage tank under
certain conditions. Plastic pipe

must not

be used, as it will not withstand the

temperature of the water generated by the solar collectors under certain conditions
(refer to Warning on page 29).

DOES THE WATER QUALITY AFFECT THE WATER HEATER?

The water heater is suitable for most public water supplies, however some water
qualities may have detrimental effects on the cylinder, solar collectors and fittings.

If

you are in a known harsh water area you must read page 38

. If you are not

sure, have your water quality checked against the conditions described on page 38.

HOW LONG WILL THE WATER HEATER LAST?

There are a number of factors that will affect the length of service the water heater
will provide. These include the water quality, the water pressure, temperature (inlet
and outlet) and the water usage pattern. However, your Rheem water heater is
supported by a comprehensive warranty (refer to page 40).

«
...
4
5
6
7
8
...
»

Содержание Solar Loline Conversion Kit Electric Water Heater









































Отзывы:

Нет отзывов

Похожие инструкции для Solar Loline Conversion Kit Electric Water Heater

Бренд: WaterLogic Страницы: 10

Бренд: WaterLogic Страницы: 4

Бренд: TDRFORCE Страницы: 12

Бренд: DAB Страницы: 184

Бренд: DAB Страницы: 184

Бренд: A.O. Smith Страницы: 6

Бренд: P.I.T. Страницы: 20

Бренд: Gude Страницы: 62

Бренд: OEG Страницы: 28

Бренд: Wilo Страницы: 76

Aquakinetic Q237

Бренд: Kinetico Страницы: 32

Бренд: Gorenje Tiki Страницы: 48

Бренд: Zoeller Страницы: 16

Бренд: STIEBEL ELTRON Страницы: 15

Бренд: hajdu Страницы: 72

Бренд: OEM Страницы: 16

sanitary T Series

Бренд: TapFlo Страницы: 24

Бренд: ProMinent Страницы: 124

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды