Rheem RTGH-84DVLN-2 Скачать руководство пользователя страница 70

Страница: 70 / 84

INSTALLATION INSTRUCTIONS

Setting the Water Temperature

WARNING:

Improper adjustment, alteration, service, or maintenance

can result in death, personal injury, property damage, and/

or product damage.

Maximum Temperature Adjustment

by the Main Remote Control (UMC–
117)

DANGER:

Water temperatures above 125°F (52°C) will result in death

and/or severe burns from scalding.

WARNING:

Refer to chart below and the scald potential warnings

on page 4 on this manual before making an adjustment.

Changing this setting is done at your own risk.

Residential water heater temperatures can be adjusted

up to 140°F (60°C). DO NOT perform the following

adjustment if a setting of up to 140°F (60°C) is not

required.

To change the temperature settings up to

140°F (60°C):

Turn on the remote control.

Turn off the gas and water to the water heater by

closing the shut-off valves.

Press the UP adjustment button repeatedly until 120°F

(49°C) shows in the LED display. Hold the UP button

until the “120” on the display starts to blink.

NOTICE:

LED display only shows °F.

Time/Temperature Relationship in Scalds

Water

Time to Produce

Temperature

a Serious Burn

120°F (49°C)

More than 5 minutes

125°F (52°C)

1 1/2 to 2 minutes

130°F (54°C)

About 30 seconds

135°F (57°C)

About 10 seconds

140°F (60°C)

Less than 5 seconds

145°F (63°C)

Less than 3 seconds

150°F (66°C)

About 1 1/2 seconds

155°F (68°C)

About 1 second

Table courtesy of Shriners Burn Institute

The contents on pages 70 through 77 should only be performed by qualified service personnel.

In-Use

Indicator

(Lit during

operation)

Priority

Indicator

Temperature

Adjustment

Buttons

ON/OFF

Button and

Indicator

LED Display

(Displays

water

temperature

and error

codes)

Star

t/Adjust

Temperature Conversion Chart

°F

°C

85 100 102 104 106 108 110 112 114 116
29 38 39 40 41 42 43 44 46 47

118 120 125 130 140 150 160 170 185 °F

48 49 52 54 60 66 71 77 85 °C

Содержание RTGH-84DVLN-2





















































































Результаты поиска

Содержание RTGH-84DVLN-2

Отзывы:

Похожие инструкции для RTGH-84DVLN-2

Бренды по названию

Популярные бренды

Rheem RTGH-84DVLN-2, Инструкция по использованию и уходу

Результаты поиска

Содержание RTGH-84DVLN-2

Отзывы:

Похожие инструкции для RTGH-84DVLN-2

Бренды по названию

Популярные бренды