Rheem P16 Series Скачать руководство пользователя страница 24

Страница: 24 / 56

Wiring

Field wiring must comply with the National Electric

Code (C.E.C. in Canada) and any applicable local

code.

Power Wiring

It is important that proper electrical power from

a commercial utility is available at the heat pump

contactor. Voltage ranges for operation are shown

below.

VOLTAGE RANGES (60 HZ)

Install a branch circuit disconnect within sight of

the unit and of adequate size to handle the starting

current (see “Electrical Data” on page 5.)

Power wiring must be run in a rain-tight conduit.

Conduit must be run through the connector panel

below the access cover (see page 6) and attached

to the bottom of the control box.

Connect power wiring to line-voltage lugs located

in the outdoor heat pump unit electrical box. (See

wiring diagram attached to unit access panel.)
Check all electrical connections, including

factory wiring within the unit and make sure all

connections are tight.
DO NOT connect aluminum field wire to the

Comfort Control

terminals.

Grounding

WARNING:

The unit must be

permanently grounded. Failure to do so can cause

electrical shock resulting in severe personal injury

or death.

A grounding lug is provided near the line-voltage

power entrance for a ground wire.

WIRING

Control Wiring (cont.)

ST-A1226-09

Operating Voltage Range at Maximum

Nameplate Voltage

Load Design Conditions for Compressors

Copeland

208/230 (1 Phase)

187 - 253

208/230 (3 Phase)

187 - 253

460

414 - 506

575

517 633

ST-A1226-09

Содержание P16 Series

























































Результаты поиска

Содержание P16 Series

Отзывы:

Бренды по названию

Популярные бренды

Rheem P16 Series, Руководство по установке

Результаты поиска

Содержание P16 Series

Отзывы:

Бренды по названию

Популярные бренды