A R C F L O O R L A M P
Wipe clean with a soft, dry cloth or static duster. Always avoid the use
of harsh chemicals or abrasive cleaners as they may cause damage to
the fixture’s finish.
IMPORTANT PLEASE READ
WE RECOMMEND INSTALLATION BY A
LICENSED ELECTRICIAN.
SAFETY INSTRUCTIONS:
ASSEMBLY & INSTALLATION:
CARE INSTRUCTIONS:
WARNINGS:
These instructions are provided for your safety. It is very important
that they are read completely before beginning the installation of your
fixture.
This lamp is equipped with a polarized plug (one blade is wider than
the other). If the plug does not fit securely into the outlet, do not force
it - contact a professional electrician. Use the plug with an extension
cord only if it can be fully inserted into the cord’s socket. Never alter
the plug in any way.
This fixture has been rated for up to two (2) 100-watt maximum Type
A medium base bulbs or two (2) 11-watt LED medium base bulb
(included). To avoid risk of fire, do not exceed the recommended
wattage.
2
**NOTE: It is recommended that two people assemble the lamp per
the following instructions to avoid injury or damage to the lamp.**
1. Remove all parts from carton. Remove protective plastic and
discard.
2. Remove bolts (H), washers (G), and plate (D) from the bottom of
column (E). Set all parts aside.
3. Place base (A) on top of loader (F). Place both items on a level
surface. Place plate (D) on top of base (A).
4. Set column (E) on top of plate (D). Threaded holes in the bottom of
column (E) should align with holes (B).
5. Hold column (E), plate (D), base (A) and loader (F) together.
Carefully tilt parts to the side as shown in Illustration 1.
6. Slip washers (G) over bolts (H). Insert bolts (H) through holes in
loader (F), base (A) and plate (D), as shown in Illustration 1. Bolts (H)
will thread into the bottom of column (E). Use wrench (C) to tighten
bolts (H).
7. Gently turn assembled base and column back into upright position.
Make sure column (E) is securely attached to base (A). If column (E)
seems loose, turn base over and tighten bolts (H) again.
8. Locate column (K) and remove screw (J) and set aside. Insert column
(K) into column (E) as shown in Illustration 2. Insert screw (J) into hole
(I) on column (E) to secure parts together. NOTE: The electrical cord
on this lamp exits column (E) just above base (A). Pull the electrical
cord exiting the column taut when inserting column (K) into
column (E) to prevent damage to the wire.
9. Locate column (L) and remove screw (N) and set aside. Insert column
(L) into column (K), as shown in Illustration 3. Insert screw (N) into
hole (M) on column (K) to secure parts together. NOTE: The electrical
cord on this lamp exits column (E) just above base (A). Pull the
electrical cord exiting the column (E) taut when inserting column
(L) into column (K) to prevent damage to the wire.
10. Lift shade (R) over socket cluster. Slide split washer (Q) between
shade washer (P) and loop (O). Lift shade (R) so the top of shade
washer (Q) is touching the bottom of loop (O). Secure position of
shade (R) by turning shade washer (P) until it rests against the
bottom of split washer (Q).
11. Install two (2) 11-watt maximum medium base LED bulbs (V) into
sockets.
12. Remove protective plastic (T) from polarized plug (S). Insert
polarized plug into electrical outlet.
13. Use on-off foot switch (U) to control power to the lamp.
All wires are connected. When unpacking, be careful not to pull wires
as a bad connection may result. Do not connect electricity until your
fixture is fully assembled. To reduce the risk of fire, electrical shock
or personal injury, always turn off fixture and allow it to cool prior to
replacing the lightbulb. Do not touch bulb when fixture is turned on
or look directly at lit bulb. Keep flammable materials away from the lit
bulb.
This lighting fixture contains lead, a chemical known to the State of
California to cause cancer, birth defects and other reproductive harm.
Wash hands after installing, handling, cleaning, or otherwise
touching this light fixture.
WARNING:
This product can expose you to lead, which is
known to the State of California to cause cancer and birth defects or
other reproductive harm. For more information, go to
www.P65Warnings.ca.gov.
THIS IS NOT A TOY AND THE PRODUCT HAS
NO PLAY VALUE.
WARNING: STRANGULATION HAZARD
Keep cord at least 3 ft away from cribs, bassinets, and toddler beds.
Keep out of reach of children under 3.
