background image

 

DTR_319-01-01-001_EN_b

 

8.

 

Additional options 

8.1

 

Operator panel 

The operator panel is a separately offered accessory (additional option) which, among others, can work with the 
device.  On the panel, there are two monostable buttons that allow you to change the information displayed by 
the signalling device. An example of the panel is shown in Fig. 9

4

 

 

 

Fig. 10 

 

9.

 

Disposal and recycling 

9.1

 

Packaging material recycling 

The  packaging  elements  must  be  segregated  and,  then,  recycled  in  accordance  with  the  local  executive 
regulations on waste disposal. 

9.2

 

Device disposal 

 
The device must not be disposed of as urban waste! 

In accordance with the directive 2002/96/EC (WEEE), if the repair of the device is not economically justified, the 
user must take the damaged or destroyed equipment to a special waste disposal centre. 

 

 

10.

 

Most common installation errors 

1

 

Invalid configuration uploaded to the light signalling device.  

2

 

Drilling additional mounting holes. 

3

 

Installation not in accordance with the manual, that is wires facing up. 

                                                           

4

 Explanatory figure, the supplied panel may differ from the presented one 

Содержание 319-01-01










Отзывы: