RFNet AP-2001G Скачать руководство пользователя страница 3

Страница: 3 / 22

End Product Labeling

This transmitter module is authorized only for use in device where the antenna may

be installed

such that 20cm may be maintained between the antenna and users (for

example: Notebook,

Access Point, Router and similar product). The final end

product must be labeled in a visible area

with the following: “Contains TX FCC

ID: PXPAP2001G’’.

Manual Information That Must be Included

The OEM integrator has to be aware not to provide information to the end

user regarding how to

install or remove this RF module in the user’s manual of

the end product which integrates this

module.

The user’s manual for OEM integrators must include the following information in a

prominent

location “IMPORTANT NOTE: To comply with FCC RF exposure

compliance requirements. The

antenna must not be co-located or operating in

conjunction with any other antenna or transmitter

and antenna must be installed such that 20cm is maintained between the antenna and users

Canada-Industry Canada (IC)

Operation is subject to the following two conditions:

1) This device may not cause interference and
2) This device must accept any interference, including interference that may cause

undesired operation of the device.

This device has been designed to operate with an antenna having a maximum gain of 0.52 dBi.
Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The
required antenna impedance is 50 ohms.

Содержание AP-2001G























Результаты поиска

Содержание AP-2001G

Отзывы:

Бренды по названию

Популярные бренды

RFNet AP-2001G, Руководство пользователя

Результаты поиска

Содержание AP-2001G

Отзывы:

Бренды по названию

Популярные бренды