background image

ZULU Telemetry 

DS-ZULUT-6 

ZuluT Evaluation Board Configuration

 

Power In

10 x 

Digital 
Inputs

2 x 

Analogue 

Inputs

RS232 Comms

(not fitted as 

standard)

USB Comms

(not fitted as 

standard)

Comms Selector Link
All centre to RS232, or
All Centre to USB
(not fitted as standard)

ZULU

Module

Antenna

Overview 

When paired together the outputs of the receiver will follow the inputs at the transmitter 

The serial outputs also provide data from the receiver 

 

To get up an running complete the following; 
1. 

Set the jumper links as below 

2. 

Screw in Antenna 

3. 

Apply power 

4. 

Pair together the receiver and transmitter board 

 

Jumper Links  

Note that the Jumper links are read on Power up only 

 

Power In

10 x 

Digital 

Outputs

2 x 

Analogue 

Outputs

(PWM)

RS232 Comms

(not fitted as 

standard)

USB Comms

(not fitted as standard)

Comms Selector Link
All centre to RS232, or
All Centre to USB
(not fitted as standard)

ZULU

Module

Antenna

Status LED’s

Reference 

Name 

When Fitted 

When Open 

J3 

A/D 

I/O 1 & 2 are  

analogue operation 

I/O 1 & 2 are set to  

Digital operation 

J3 

Channel Select 

Zulu operates on Channel A 

Zulu operates on Channel B 

J4 

TX/ RX Select 

Zulu set as Transmitter 

Zulu set as Receiver 

J4 

(Transmitter) 

Watchdog  

Enable 

Watchdog enabled 

Watchdog Disabled 

J4 

(Receiver) 

PWM 

Enable 

Enables PWM Output 

Output’s 1& 2 set to 

Digital 

LK1-LK4 

Comms  

Select 

All links from Centre to USB 

All links from Centre to RS232 

N/A 

LK5 

(Receiver) 

PWM Supply 

Vcc: PWM is powered from Vcc 

VSUPPLY: PWM is powered 

from incoming V supply at TB1 

 

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Содержание ZULU-T868


















Отзывы: