Reynolds Building Systems Best Barns USA North Dakota Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 19

background image

3.

Install soffit panels on the

opposite side. Start with a
24" long panel that has a
'LAP' edge.

Step 15 Set Roof Trusses

Rear Gable

Step 16 Install Eave Soffit

Set roof trusses. Secure trusses to metal
hangers with 1-1/2" hanger nails.

1.

Locate a 5" wide x 24" siding panel that has a 'tongue' edge. Install this panel under the truss

overhang at the rear of the building. Install the siding/soffit panel with the beveled edge flush
with the end of the trusses and the cut edge against the gable siding. Use 6d galv. nails.

2.

Install (3) three, for 12' building, or (4) four, for 16' building, more full length siding panel

under the trusses. Cut the last panel to fit.

4.

Locate (4) four 87-3/4" 1x4 trim boards.

Cut length flush with bottom of sidewall
siding and install at corners.

Soffit

Beveled Edge

«
...
12
13
14
15
16
...
»

Содержание Best Barns USA North Dakota




















Отзывы:

Нет отзывов

Похожие инструкции для Best Barns USA North Dakota

Бренд: Palmako Страницы: 53

Бренд: Palmako Страницы: 57

Бренд: Palmako Страницы: 31

Бренд: Palmako Страницы: 29

Бренд: Palmako Страницы: 30

Бренд: Palmako Страницы: 82

Бренд: Palmako Страницы: 118

Бренд: Jimmy at work Страницы: 31

Бренд: Gazebo penguin Страницы: 8

Heartland CLASSIC GENTRY GABLE 12' x 12'

Бренд: Backyard Products Страницы: 84

12x12 Space Maker Garden Shed with Plywood Roof & AK...

Бренд: OLT Страницы: 42

Бренд: Palmako Страницы: 29

Бренд: Palmako Страницы: 102

Бренд: Palmako Страницы: 31

FRB34-3553-1FSC

Бренд: Palmako Страницы: 69

TEA HOUSE PERGOLA

Бренд: Grange Fencing Страницы: 8

Devon FRB44-3535

Бренд: Gudrum Страницы: 22

Бренд: Dobrosfera Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды