Reyax RSS8833 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 31

Reyax RSS8833 Скачать руководство пользователя страница 9

Copyright

©

2020, REYAX TECHNOLOGY CO., LTD.

9

RYS8830 RYS8833

`GNSS Module Software Guide

8.

GPS almanac data acquisition

Syntax

Response

@GALG

[GALG] Done

This command is used to acquire the GPS almanac data received by RYS8830. When the
command is received, the RYS8830 transmits the GPS almanac data (binary data) to the host
controller.
The GPS almanac data size is 2048 bytes. In addition, the data which is actually transferred
has the header and footer added.

This command must be issued at “Idle” mode.

Argument: None

9.

GPS almanac data injection

Syntax

Response

@GALS

[GALS] Done
[GALS] Ready

This command is used to inject the GPS almanac data into the RYS8830. Transmit the GPS
almanac data (binary data) following the Ready response from the RYS8830.
The GPS almanac data size is 2048 bytes. In addition, the data which is actually required has
the header and footer added.

This command must be issued at “Idle” mode.

Argument: None

10.

Cold start

Syntax

Response

@GCD

[GCD] Done

This command is used to start the positioning with cold start.

Argument: None

11.

GPS ephemeris data acquisition

Syntax

Response

@GEMG

[

GEMG

] Done

This command is used to acquire the GPS ephemeris data which has been received by the
RYS8830. When the command is received, the RYS8830 transmits the GPS ephemeris data
(binary data) to the host controller.
The GPS ephemeris data size is 3072 bytes. In addition, the data which is actually transferred
has the header and footer added.

This command must be issued at “Idle” mode.

Argument: None

«
...
7
8
9
10
11
...
»

Содержание RSS8833
































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды