3
14. To prevent serious injury, do not use the
tool to cut wood, diamond, magnesium
or magnalium workpiece.
15. Wear safety goggles and hearing
protection during operation.
16. Check lower guard for proper closing
before each use. Do not operate the
saw if lower guard does not move freely
and close instantly. Never clamp or tie
the lower guard into the open position.
If saw is accidentally dropped, lower
guard may be bent. Raise the lower
guard with the retracting handle and
make sure it moves freely and does not
touch the blade or any other part, in all
angles and depths of cut.
17. Check the operation of the lower guard
spring. If the guard and the spring are
not operating properly, they must be
serviced before use. Lower guard may
operate sluggishly due to damaged
parts, gummy deposits, or a build-up of
debris.
18. Lower guard should be retracted
manually only for special cuts such
as ″plunge cuts″ and ″compound
cuts.″ Raise lower guard by retracting
handle and as soon as blade enters
the material, the lower guard must be
released. For all other sawing, the lower
guard should operate automatically.
19. Always observe that the lower guard is
covering the blade before placing saw
down on bench or floor. An unprotected,
coasting blade will cause the saw to
walk backwards, cutting whatever is in
its path. Be aware of the time it takes
for the blade to stop after switch is
released.
20. DO NOT USE THIS METAL CUTTER
WITH THE SAW BLADE HELD UPSIDE
DOWN IN A VISE. The saw is not
designed for such use and cannot be
used safely in that position.
Special Safety Rules For Kickback
1. Causes and Operator Prevention of
Kickback:
●
Kickback is a sudden reaction to a
pinched, bound or misaligned saw
blade, causing an uncontrolled tool
to lift up and out of the workpiece
toward the operator.
●
When the blade is pinched or bound
tightly by the kerf closing down, the
blade stalls and the motor reaction
drives the unit rapidly back toward
the operator.
●
If the blade becomes twisted or
misaligned in the cut, the teeth at
the back edge of the blade can dig
into the top surface of the workpiece
causing the blade to climb out of the
kerf and jump back toward operator.
2. Kickback is the result of tool misuse
and/or incorrect operating procedures or
conditions and can be avoided by taking
proper precautions as given below:
●
Maintain a firm grip with both hands
on the tool and position your body
and arm to allow you to resist
KICKBACK forces. KICKBACK forces
can be controlled by the operator, if
proper precautions are taken.
●
When blade is binding, or when
interrupting a cut for any reason,
release the trigger and hold the
tool motionless in the material until
the blade comes to a complete
stop. Never attempt to remove
the tool from the work or pull the
tool backward while the blade is in
motion or KICKBACK may occur.
Investigate and take corrective
actions to eliminate the cause of
blade binding.
Содержание MC1850R
