User's Manual
User's Manual
12
13
8. USB Function
The unit with built-in USB port supports the following devices:
!
USB portabe hard disc
!
USB memory
USB function as listed below:
- PVR(Personal Video Record)
- Timeshift record
- Audio/Video file display
- Photo display
- Software Upgrade
- Format disk
- Delete/Rename disk file
- Device Info display
USB Browser
There are two parts under this menu:disk partition list and file list. User can switch between two lists with
left /Right
keys. While the cursor in partition list, press
OK
key to choose disk partition. While the cursor in
file list, press
OK
key to enter directory or start to play current file.
Green
key to play the current file.
Blue
key to stop playing.
Yellow
key to enter volume adjust menu.
Red
key to ener USB functions list and detailed direction as follows:
Delete
-- Delete current file
Rename
-- Change the current file name
Show MP3
-- Switch to the mode which only display MP3 file.
Show PVR
-- Switch to the mode which only display PVR record file.
Show Jpeg
-- Switch to the mode which only display JPEG file.
Show BIN
-- Switch to the mode which only display .bin file.
Show All Files
-- Switch to the mode which display all supported files.
Format Disk
-- Formatting the disk
Show Disk Information
-- Display current disk partition informaitn, such as: Capacity, File system type,
Used space and Free space.
Set Record Path
-- Place all recorded files into a folder by set record file path.
Switch to Order(Random) Play
-- Set order or random play.
Switch to Auto(Manual) Play
-- Set auto or manual play.
PVR Function
User can record any audio and video data to hard disk and watch these programs afterwards. There are
two record modes which is manually recorded or recorded by timer. For the manual record, you can record
another program under the current TP while watching the current program. Under the mode of manual
record, there will appear the channel list for
recording as the right picture for user to
choose what to record.
Record and Play menu:
Time shown in the left tells the timer duration
of playing and right time tells the total
recorded time.
2XF Type(1 Input/1 Loop Through)
950 to 2150 MHz
- 65 to 25 dBm
22KHz
13.0 +0.5V/16V +0.7V, Max 500Ma
QPSK/FRC Coding(DVB prETS 300 421)
2<Rs<45 Mband(SCPC/MCPC)
MPEG-1 layer I and II / Musicamr
Stereo Channel/Dual Mono/Joint Stereo/ Mono
MPEG-2 Main Profile @ Main Levels With Lette
64 Mbits of SDRAM is provided
Up to 15Mbits/s (Max. burst rate: 228 Mbits/s)
PAL-25 frame @720 x 576; NTSC-30 frame @720x480
4:3, 16:9
100 - 240V AC @ 50Hz/60Hz±5%
Max. 30W
1 RF Input / 1 RF Loop through output
RF OUT / RF IN
2 x Audio L/R (RCA)
1 x Video Signal (RCA)
1 x RS-232 (9-pin D-sub male)
1 x Y/Pb/Pr Video Signal (3RCA)
1 x ETHERNET
TRANSMISSION STANDARDS
DVB-S, MPEG-2
SATELLITE INPUT/DEMODULATION
Connector Type
Input Frequency
Signal Input Level
Band Switch Control
LNB Supply
Demodulation Type
Symbol Rate
AUDIO/VIDEO PROCESSING
Audio Decompression
Audio Outputs
Video Decompression
Video Buffer
Data Rate
Video Output
Video Format
POWER SUPPLY
Main input voltage
Power consumption
REAL PANEL
Connections
Problem
No display light up on front panel
No sound or picture, but the front
panel red light is ON.
No sound or picture
Bad picture/Blocking Error
No picture(Video)
There is interference on your
digital satellite channel.
The RCU is not working.
What To Do
Check whether power cord has been plugged
properly into power socket.
Press the standby button.
Adjust the dish. Check the Signal Level in the
Antenna Setup Menu
Check the cable connections. LNB and other
equipment connected between the LNB and the
receiver and adjust the dish.
Adjust the dish.
Connect a signal attenuator to the LNB input
Change to a larger dish
Change to an LNB with lower noise factor
Change the LNB
Check the UHF channel fixed in your system and
tune the UHF properly.
Change the receiver output channel to a more
suitable channel or connect the system using
SCART cable.
Change the battery
Aim the RCU at the unit, and make sure no blocks
between the front panel and RCU
Possible Causes
Power Cord is not well plugged
The unit is in standby mode
The satellite dish is not pointing at the satellite.
No signal or weak signal
The satellite dish in not pointing at the satellite
Signal is too strong
Satellite dish is too small
LNB noise factor too high.
The LNB is faulty.
The system is connected by SCART cable and
TV is not in AV/EXT mode.
The system is connected using RF cable and the
output channel of the receiver interferes with an
existing terrestrial channel or Video Signal.
Out of battery
RCU is aimed at wrong direction
9. Technical Specification
10. Trouble Shooting
Note:
If you still cannot resolve the problem with above reference. Please contact the local dealer or their after-sales service center.
