In thermostatic mode this value is displayed constantly
if external sensor is connected (then internal one is invalid).
5.
Manual and program mode
Press and hold
(till icons and
starts to flash)
and subsequently:
- press
to activate manual mode
- press
to activate program mode
- press to define time, data and supply schedule with
and
6.
Set weekly schedule
Adjusting/setting the schedules can only be carried out
when thermostat is in programable mode.
Press
to define periods and set the tempera-
ture for
weekdays (“1 2 3 4 5” will show along)
as following:
minute
→
hour
→
temperature adjusting
Then do the same for weekend (“6” & “7” will show along
the left of the screen) by using ,
and
. An example
of weekly schedule you can find in table below.
Time
display
WEEKDAY
(MONDAY –
FRIDAY)
(1 2 3 4 5 shows
on screen)
WEEKEND
(SATURDAY)
(6 shows on
screen)
WEEKEND
(SUNDAY)
(7 shows on
screen)
Time
Temp.
Time
Temp.
Time
Temp.
Period 1
06:00
20
°C
06:00
20
°C
06:00
20
°C
Period 2
08:00
15°C
08:00
20
°C
08:00
20
°C
Period 3
11:30
15°C
11:30
20
°C
11:30
20
°C
Period 4
13:30
15°C
13:30
20
°C
13:30
20
°C
Period 5
17:00
2
2°C
17:00
20
°C
17:00
20
°C
Period 6
22:00
15°C
22:00
15°C
22:00
15°C
7.
Setting functions and options
During power off, press and hold
and
at the same
time for 5 sec. to go to system functions. Then press
to change the different items. Press
or
to set
the relative values according to the table.
No.
Function
Settings & Options
Default
1 Temp. calibration
-9 -
9°C
-
2°C*
2
Invalid
3 Lock
00: All buttons are locked except POWER
01: All buttons are locked
01
4 Heating / Cooling
00: Cooling only
01: Heating / Cooling
02: Heating only
01
5
Invalid
6
Invalid
7 12 / 24 Clock
00: 12 h; 01: 24 h
01
8 Display mode
00: Display both set and room temp.
01: Display set temp. only
00
9 Deadzone temp.
1 -
5°C
1°C
A Modbus IP address 0X00-0XFF
01
B baudrate
01: 9600; 02: 19200; 03: 38400;
04: 56000; 05: 115200
01
C Working mode
00: Thermostatic mode
01: Temperature difference mode
00
D Version number
The number of the device
202
* when you using external sensor in thermostatic mode change the value to 0
°
C
The controller HMI SINGLE can work in one of two modes:
•
thermostatic mode
–
the device is switched on / off
if the room temperature falls below the temperature set
on the controller
(or rises above
this temperature
if the controller is in cooling mode)
•
temperature difference
mode
- in this mode the external
sensor must be connected because both temperatures
(i. e. from external and internal sensors) are used to calculate
the temperature difference (as
subtraction ‘
external sensor
temperature
’
minus
‘
internal sensor temperature
’
in heating
mode and
‘
internal sensor temperature
’
minus
‘
external sensor
temperature
’
in cooling mode). If this difference is lower then
set temperature difference the fan is off, otherwise it is on. This
mode is dedicated for destratification fan.
Wiring diagram
Installing
This product is suitable for box 86 x 86 mm or
Ø 60 mm.
1.
Connect the wire of power and other equipment into
the terminals.
2.
Fix the wall plate into the wall box by a screwdriver.
3.
Connect the LCD board into the wall plate.
WARNING:
Please arrange the professional
technician to install this product according to installation
drawing and instruction.
RISK OF ELECTRICAL SHOCK:
Disconnect power supply
before
making
electrical
connection.
Contact
with components carrying hazardous voltage can cause
electrical shock and may result in severe personal injury
or death.
