manualshive.com logo in svg

Reveal ZERO ZONE, Руководство по установке и эксплуатации, Страница: 16 / 25

Поделиться
Скачать
Reveal ZERO ZONE Скачать руководство пользователя страница 16

14  •  Installation & Operation

INSTALLATION & OPERATION

Mirrors

Mirror assemblies include the mirrors, brackets, supports, and an air deflector, which are shipped together as a kit.

1.  Assemble the support brackets to the mirror support. Slide the tabs on the brackets into the slots in the mirror support. Use the supplied 

hex screws to fasten the brackets in place (

See Figure 20

). 

Note: There will be 3 brackets and 3 screws for 36" wide mirrors or 

 

4 brackets and 4 screws for 48" wide mirrors.

2.  Install the mirror support into the shelf standards, using both the second and third slots from the top (

See Figure 21

).

 FIGURE 20: Support Brackets and Mirror Support

Support 

Bracket

Mirror 

Support

Add Hex 

Screws

 FIGURE 21: Install Mirror Support into the Shelf Standards

Install into second 

and third slots 

from the top

 FIGURE 22: 

Shelf Standard Slots for Air Deflector

MIRROR HEIGHT

SLOT FOR AIR DEFLECTOR

8" Tall

6th Slot from Top

12" Tall

9th Slot from Top

20" Tall

16th Slot from Top

24" Tall

19th Slot from Top

 FIGURE 23: 

Install Air Deflector Under Mirror Support

Install into shelf 

standards

Air 

Deflector

 FIGURE 24: Hang the Mirror, Insert Top First

First insert into the top brackets, 

then into the bottom brackets

Mirror

3. 

Install the air deflector (also called a “mirror scoop”) into the shelf standards 

under the mirror support. Refer to the table for the correct slot, counting down 

from the top (

See Figure 22

 

and Figure 23

).

4.  peel the protective coating off of the mirror. Hang the mirror from the brackets. 

Start by inserting it into the top and then the bottom (

See Figure 24

).

5.  Center the mirror for optimal product display.

Содержание ZERO ZONE


























Отзывы:

Нет отзывов