Retsch ABP 250 Скачать руководство пользователя страница 17

Страница: 17 / 57

Packaging, Transport and Installation

4.1 Packaging

The packaging has been adapted to the mode of transport. It complies with the generally
applicable packaging guidelines.

NOTICE

N3.0001

Complaint or return

Keeping the packaging



Inadequate packaging and insufficient securing of the device can

jeopardise the warranty claim in the event of a complaint or return.

•

Keep the packaging for the duration of the warranty period.

4.2 Transport

DANGER

D2.0001

Serious personal injury

Suspended loads



If dropped, the great weight of the device would result in serious injuries

or death.

•

People must never stand below suspended loads!

NOTICE

N4.0017

Damage to components

Transport



Mechanical or electronic components may be damaged during transport.

•

The device must not be knocked, shaken or thrown during transport.

NOTICE

N5.0014

Complaints

Incomplete delivery or transport damage



The forwarding agent and Retsch GmbH must be notified immediately in

the event of transport damage. It is otherwise possible that subsequent
complaints will not be recognised.

•

Please check the delivery on receipt of the device for its
completeness and intactness.

•

Notify your forwarding agent and Retsch GmbH within 24 hours.

Содержание ABP 250


























































Результаты поиска

Содержание ABP 250

Отзывы:

Похожие инструкции для ABP 250

Бренды по названию

Популярные бренды

Retsch ABP 250, Руководство пользователя

Результаты поиска

Содержание ABP 250

Отзывы:

Похожие инструкции для ABP 250

Бренды по названию

Популярные бренды