manualshive.com logo in svg

Resol DeltaSol CS Plus bidirectional, Руководство для специализированного ремесленника

Поделиться
Скачать
Resol DeltaSol CS Plus bidirectional Скачать руководство пользователя страница 56

en

56

Installation

Indications,

 functions and options

Messages

Commissioning

Operation and function

PWM feedback signal

PFB1, PFB2
PWM feedback signal
Adjustment range: OFF, A, b
Factory setting: OFF
(A = Wilo pump, b = Grundfos pump)
With this parameter, the type of the PWM feedback signal of a bidirectional HE 
pump can be adjusted. The signal transmits either a flow rate between 0 … 2100 l/h 
or an error message.
The following messages can be displayed:
Err1:  PWM interface of the pump defective
Err2:  The pump is not running optimally, external cause electronics (e. g. overvolt-

age, low voltage)

Err3:  The pump stops, but is operable, external cause electronics (e. g. overvoltage, 

low voltage)

Err4:  The pump stops, but is operable, external cause installation / hydraulics
Err5:  The pump stops, but is not operable, internal cause electronics / pump is stuck
Err6:  PWM feedback signal connection defective

Note
If there is an error, the flow rate will not be indicated and the heat quan-
tity measurement will not be carried out.

Maximum store temperature

S  MX / S1MX / S2MX
Maximum store temperature
Adjustment  range:  4 … 95 °C  [40 … 200 °F]
Arr  10:  4 … 90 °C  [40 … 190 °F]
Factory setting: 60 °C [140 °F]
If the store temperature reaches the adjusted maximum temperature, the store will 
no longer be loaded in order to avoid damage caused by overheating. A non-adjusta-
ble hysteresis of 2 K [4 °Ra] is set for the maximum store temperature.
If the maximum store temperature is exceeded, 

☼

 is displayed. 

Note
If the collector cooling or the system cooling function is activated, the 
adjusted maximum store temperature may be exceeded. In order to pre-
vent system damage, the controller is also equipped with an integrated 
store emergency shutdown, deactivating the system if the store reaches 
95 °C  [200 °F].

Store emergency shutdown

OSEM
Store emergency shutdown option
Adjustment range: ON, OFF
Factory setting: OFF
This option is used for activating the internal store emergency shutdown for an up-
per store sensor. If the temperature at the reference sensor exceeds 95 °C, store 1 
will be blocked and loading will be stopped until the temperature falls below 90 °C.

Note
Sensor S3 is used as the reference sensor in systems 1, 2, 3, 8, 9 and 10. In 
systems 6 and 7, sensor S4 is used as the reference sensor. The option is 
not available in systems 4 and 5 and it will only be available in systems 6 
and 7 if the heat quantity measurement option is not activated.

Содержание DeltaSol CS Plus bidirectional









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды