manualshive.com logo in svg

Resol DeltaSol BX, Руководство пользователя

Поделиться
Скачать
Resol DeltaSol BX Скачать руководство пользователя страница 25

en

25

Installation

Indications,

 functions and options

Messages

Commissioning

Operation and function

 System 17: 2-store solar system with pump logic and heat exchange control

The controller compares the temperature at sensor S1 to the temperatures at 
sensors S2 and S4. If the measured temperature differences are higher than the ad-
justed switch-on temperature differences, the pump (R1 and/or R2) will be activat-
ed and the corresponding store will be loaded up to the adjusted store maximum 
or set temperature respectively at most. The priority logic effects prior loading of 
store 1.
Heat exchange control to an existent store via an additional pump (R3) can be 
carried out with another temperature differential function (S3 heat source / S4 
heat sink).

Sensors

S1

Temperature collector

1 / GND

S2

Temperature store 1 
base

2 / GND

S3

Temperature heat 
exchange source

3 / GND

S4

Temperature store 
2 base and heat 
exchange sink

4 / GND

S5

Free

5 / GND

Relay

R1

Solar pump store 1

R1 / N / PE

R2

Solar pump store 2

R2 / N / PE

R3

Store loading pump

R3 / N / PE

R4

Free

 R4 /R4

R3

R1

R2

S4

S3

S2

S1

Temp. Sensor

Pt1000

L

R3

R2

R1

GND

S1

S2

S3

S4

S5

VBus

PW

M

1

PW

M

2

N

R4

V40

VBus GN

D

L'

VFS

RPS

Содержание DeltaSol BX













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды