Operation
• Start the operating system (e.g. at least Windows 2000/XP or later) or the Android device.
• Connect the USB receiver to the computer. The operating system recognizes the new hardware (USB
keyboard and USB mouse) and installs the necessary driver (included in the operating system). The
same applies if the USB receiver is connected to an Android device.
• The product is ready for operation on concluding the driver installation.
Operation
• Two functions levels can be selected with the “Fn” button:
1 LED is off: Mouse cursor arrow
2 LED lights up: Multimedia buttons (increase volume (“VOL+”) or reduce volume (“VOL-”), Mute
(“MUTE”), fast forward/jump forward (“FF”), rewind/return (“REW”) as well as play/pause (“PLAY/
II
”)
• The rippled surface at the upper end of the control unit serves as a touchpad, similar to a notebook. The
surface marked on the right edge functions like the scroll wheel of a mouse. The left/right mouse button
is marked with a picture (however, the function level for the mouse operation must be activated, see
above).
• The “Esc” key corresponds with the ESC key of a PC keyboard. The key with the house symbol starts
the explorer with windows. The key with the 3x3 keyboard has different functions depending on the
operating system , e.g. a virtual keyboard fade-in with Android devices.
• If there is no user operation the control unit switches itself off after certain time to save power. Then
press a desired key for reactivation.
• The USB receiver and control unit are already tuned into each other on delivery. Keep a distance of
approximately 30 cm between the USB receiver and control unit if a renewed tuning in procedure is
required and keep the “Esc” key pressed down at the control unit for 3 seconds (the USB receiver must
be supplied with power for this tuning in procedure. Fully charged batteries must be installed in the
control unit).
• If the touchpad does not function properly press the right mouse button at the control unit (first select
the correct functions level. LED light must go out. See above).
Maintenance and cleaning
Apart from the occasional battery change the product is maintenance free. There are no components
inside the product which need to be maintained by you.
To clean the product, a dry, soft and clean cloth is sufficient. Touching the housing too hard (special trans-
parent cover and touchpad) can cause scuffs.
Do not use any aggressive cleaning agents, cleaning alcohol or other chemical solutions as they can
cause damage to the housing and malfunctioning.
Disposal
a) General
At the end of its service life, dispose of the product in accordance with applicable regulatory
guidelines.
Remove any inserted (rechargeable) batteries and dispose of them separately from the
product.
b) (Rechargeable) batteries
You as the end user are required by law (Battery Ordinance) to return all used batteries/rechargeable
batteries. Disposing of them in the household waste is prohibited.
Contaminated batteries/rechargeable batteries are labeled with this symbol to indicate that
disposal in the domestic waste is forbidden. The designations for the heavy metals involved
are: Cd = Cadmium, Hg = Mercury, Pb = Lead.
Used (rechargeable) batteries as well as button cells can be returned free of charge to collection points
in your municipality, our stores or wherever (rechargeable) batteries are sold.
You thus fulfill your statutory obligations and contribute to the protection of the environment.
Declaration of Conformity (DOC)
We, Conrad Electronic, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare that this product con-
forms to the fundamental requirements and the other relevant regulations of the directive 1999/5/EC.
The Declaration of Conformity for this product can be found at: www.conrad.com
Technical data
a) Control unit
Power supply ..................................................... 2 batteries of type AAA/Micro
Transmission frequency .................................. 2.4 GHz
Range .................................................................. up to approx. 20 m
Measurements .................................................. 128.5 x 44 x 15.3 mm (L x B x H)
Weight ................................................................. 46 g (without batteries)
b) USB Receiver
Power supply .................................................... via USB
Connection ......................................................... USB2.0
G
Operating Instructions
“Touch Air R01“ for TV and PC
Item no. 1217854
Intended use
The product controls a computer (or compatible Android device) by wireless. The model is ideal for con-
trolling presentation or multimedia programs. Also other programs or the user interface of an operating
system can be controlled by means of an integrated touchpad and two mouse buttons.
The control unit is powered by batteries.
It is imperative that you follow the safety instructions and all other information contained in this user
manual.
This product complies with the statutory national and European requirements. All company names and prod-
uct names are trademarks of their respective owners. All rights reserved.
Delivery content
• Control unit
• USB receiver
• Operating instructions
Description of symbols
This symbol informs you about specific risks when handling, operating or using the product.
The “arrow” symbol indicates special remarks and notes for operation.
Safety instructions
In case of damage caused by non-observance of these operating instructions, the warranty
gets void! We are not liable for any consequential damage!
We are not liable for property damage or injuries caused by improper use or failure to
observe the safety instructions! Such circumstances will void the warranty!
• Unauthorized modifications and/or alterations to the product are not permitted due to
safety and approval reasons (CE).
• The product is intended for use in dry, indoor spaces only. The product may not become
moist or wet.
• This product is not a toy, keep it out of the reach of children.
• Use in spaces with a great amount of dust, with flammable gases, vapors or solvents is not
permitted. There is a danger of fire and explosion!
• Do not leave packaging materials lying about, they may become a dangerous plaything in
the hands of children.
• Handle the product with care; impacts, blows or falling from even low heights can cause
damage.
Battery / rechargeable battery information
• Keep (rechargeable) batteries out of the reach of children.
• Do not leave batteries lying around. There is a risk that children or pets swallow batteries. If a battery
has been swallowed, seek medical advice immediately.
• Leaking or damaged (rechargeable) batteries can cause burns when in contact with skin. You should
thus wear suitable gloves in such a case.
• Chemicals running out of batteries/rechargeable batteries are very aggressive. Extensive damage may
be caused to objects or surfaces which come into contact with these chemicals. Therefore keep bat-
teries/rechargeable batteries in a suitable place.
• Do not short-circuit and disassemble batteries. Do not throw into fire. There is a risk of explosion!
• Do not recharge common batteries that are not rechargeable. There is a risk of explosion! Only use
batteries exclusively provided for this. Use a suitable charger.
• Do not mix batteries or rechargeable batteries . Either use batteries or rechargeable batteries.
• Do not mix any batteries or rechargeable batteries with different capacities (e.g. full or half full batteries
or rechargeable batteries).
• Always replace the whole set of batteries/rechargeable batteries.
• Please note the correct polarity (plus/+ and Minus/-) when inserting the batteries/rechargeable batteries.
• If you want to use rechargeable batteries please ensure that the reduced output voltage (batteries
1.5 V, rechargeable batteries - 1.2 V) does not lead to a reduction in the operating time and a reduction
in LED brightness.
Therefore we recommend you only use high quality alkaline batteries for operating the control unit to
ensure long and fault free operation.
Inserting batteries, changing batteries
• Open the battery compartment at the rear of the control unit and insert two type AAA/Micro batteries
with the correct polarity (please note: plus/+ and minus/-) Reclose the battery compartment.
• It is recommended changing the battery when the wireless range is greatly reduced or the computer no
longer reacts to the control commands of the presenter.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© Copyright 2014 by Conrad Electronic SE.°
V1_0814_02/VTP
