This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
© Copyright 2016 by Conrad Electronic SE.
1452034_V1_0716_02_VTP_m_en
Assembly
When drilling the bores and tightening the screws, make sure not to dam-
age any power lines or gas or water pipes distributed below the surface. The
assembly and the installation of the device must be carried out by a special-
ist who is familiar with the hazards and the relevant regulations. The mainte-
nance, operation and commissioning of this product may only be carried out
by qualified personnel.
When choosing a location for your device, make sure to avoid vibration, dust,
hot and cold temperatures and dampness. When using a fog machine, make
sure that the LED light effect is not subjected to a direct stream of fog.
The light effect may only be operated in locations where the ambient tempera-
ture is less than 40 °C.
Never cover the unit. When installing with other equipment, make sure that
there is sufficient ventilation. Keep a sufficient distance from other devices
and walls. Do not install the device near heat sources. Do not point any strong
beams or light sources onto the device. This may lead to overheating (risk of
fire).
Do not drill or screw additional screws in the housing in order to fasten the
device. Contact with dangerously high voltages could become possible.
The device must be mounted out of normal reach.
Illuminated objects must be at least 0.5 m away from the device’s light outlet.
Easily-flammable materials, such as decorative fabrics too, must be at least
0.5 m away from the device. Otherwise, such materials may catch fire!
Never apply filter films, masks, or other materials on the light output. This can
cause heat damages or fire risk.
During installation and servicing, the area below the installation site must be
cordoned off.
The installation surface, or mounting fixture, must be designed so that it can
withstand ten times the loading capacity for at least one hour without perma-
nent damaging deformation.
It is also essential that the device is secured by means of a second safety
restraint, which is separate from the proper mounting supports, when it is
installed in an elevated position. If the main supports fail, no part of the instal-
lation should be able to fall down.
Observe all the relevant regulations in your country when installing the de-
vice.
Acceptance test (in case of industrial/public use):
Before using the product for the first time and after any significant modifications, the
installation (including the electrical connections) must be checked by a specialist.
An annual check by a technical expert is required.
• The device can be freestanding or mounted with the mounting bracket.
• For elevated installation, secure the effect spotlight with the mounting bracket to the ceiling
or a suitable crossbar system. For installation with a screw, there is an attachment hole in
the mounting bracket. During installation, make sure that the device cannot swing freely. Use
mounting materials that are compatible with the fastening surface and capable of bearing the
weight of the light effect device.
• When installing in an elevated location, also secure the device with a suitable safety restraint
cable or safety net. The safety restraint cable or net must be capable of supporting the light
effect device in the event of a fault in the main support system.
• Set the desired inclination angle and tighten the two locking screws on the mounting bracket
securely.
For commercial or public use, a number of regulations and restrictions are to
be observed, which are described here only in excerpts. You as the operator
are responsible for seeing that these regulations must be observed in the
installation and operation.
Mains connection
The mains socket to which the light effect device is connected must be in
close vicinity to the device and easily accessible, so the device can be quickly
isolated from the mains power supply in the event of a fault.
Be careful when handling the mains cables and mains connectors. Mains volt-
age may cause fatal electric shocks.
Make sure that the connecting cable is not pinched or damaged by sharp
edges when making the connection.
Do not leave the cables trailing free; route them in an orderly and professional
manner to prevent accidents.
Before plugging in the mains plug make sure the voltage indicated on the light
effect device is compatible with the mains voltage available. Do not connect
the device if the data doesn’t match the available mains voltage. The wrong
supply voltage may lead to irreparable damages to the device and involve
risks for the user.
• Insert the IEC plug of the mains cable into the IEC mains connection on the device.
• Plug the power plug of the mains cable into an earthed wall socket.
Start-up
After connecting the power plug to the power grid, the device is ready for use.
• The mains switch on the back of the device is used to switch the appliance on and off.
• By means of the potentiometer on the back of the device, you can adjust
the sensitivity of the sound-to-light control to the volume of the music. Use a
suitable screwdriver to do this.
Adjust the potentiometer so that the light effect changes to the beat
of the music.
Replacing the Fuse
If you have to replace fuses, ensure that you only use fuses of the same type and rated current
(see „Technical data“).
Fixing fuses or bridging the fuse holder is not permitted.
• Disconnect the product from the mains supply before each fuse replacement. To do this,
pull the mains plug out of the outlet and separate the IEC plug from the mains connection
on the device.
• Use a suitable screwdriver to carefully lever out the fuse carrier on the mains connector.
• Remove the faulty fuse and replace it with a fuse of the same type.
• Carefully push the fuse holder with the new fuse back into its holder in the mains connection.
• Only then may you reconnect the device to the mains and place it back into operation.
Maintenance and cleaning
The product is maintenance-free. The product contains no parts that require servicing. There-
fore, do not open it. The LED bulb is permanently installed and cannot be replaced.
• Disconnect the product from the mains supply before each cleaning procedure.
• The device can heat up during operation. Do not touch the housing when in operation. Allow
the light effect device to cool down after operation before you touch or clean the housing.
• Never use aggressive cleaning alcohol or other chemical solutions, since these could dam-
age the enclosure or even impair operation.
• Use a dry, lint-free cloth to clean the product.
Live components may be exposed when the covering is opened or compo-
nents are removed.
Other service work or repairs may be carried out only by qualified personnel
who are familiar with the hazards involved and the relevant regulations.
Disposal
Electronic devices are recyclable material and do not belong in the household
waste. Dispose of an unserviceable product in accordance with the relevant statu-
tory regulations.
Technical data
Input voltage/current ..................... 100-240 V/AC, 50-60 Hz
Power input .................................. 12 W
Fuse .............................................. F2A L/250 V
LEDs ............................................. 3x 3 W (1xR; 1xG; 1xB)
Operating conditions ..................... 0 °C - 40 °C / 20% - 90% humidity
Dimensions ................................... 180 x 155 x 108 mm (L x W x H)
Weight .......................................... 1.0 kg
