b) Removing the clips
1
2
• Carefully and completely push the clip hook
out of the holder.
• Remove the clip.
c) Assembly and settings
Attention!
The screw connections can be fully unscrewed. Keep that in mind when making
adjustments, and hold the holder and the iPad when making adjustments, in order for
the iPad not to fall down.
5
5
4
4
3
3
1
2
5/8
3/8
You can only use the arm as
extension or adapter of a 3/8
thread on a 5/8 thread.
You may also attach a microphone holder to the arm
and attach the iPad holder directly to the tripod thread.
d) Installing/removing an iPad
• Carefully position the iPad in the clips and press it down for it to lock into place.
• Carefully push the iPad out of the clips and remove it.
Technical data
Max. load ................................................................................4 kg
Arm length ..............................................................................192.5 mm
Suitable iPads ........................................................................iPad 1, 2, 3, Air 1, Air 2, mini
Operational and storage conditions ..................................-10 to +80
°
C, 1 - 80 % RH
Holder dimensions (W x H x D) ...........................................245 x 193 x 16 mm (iPad 1)
245 x 189 x 11 mm (iPad 2, 3)
243 x 74 x 11 mm (iPad Air 1, 2)
204 x 140 x 11 mm (iPad Mini)
Weight .....................................................................................400 g
Operating instructions
IS601 iPad holder
Item no. 1384399
Intended use
The product is a holder for suitable iPads and is intended for use on table edges or pipes with a
maximum thickness of 28 mm. Use the product only for mounting a suitable tablet.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use the
product for purposes other than those described above, the product may be damaged. Read the
instructions carefully and keep them. Make this product available to third parties only together
with its operating instructions.
This product complies with the statutory national and European requirements. All company names
and product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Holder
• Bracket
• 5 x Clips
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on proper
handling in this manual, we assume no liability for any resulting personal injury or
damage to property. Such cases will invalidate the warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become
dangerous playing material for children.
• The product is intended for use in dry indoor spaces.
• Verify that the shipment is complete before assembling the product. Do not assemble
the product if the shipment is not complete.
• Assembling the product in an unsuitable location can lead to property damage and
personal injury!
• Exercise caution when assembling the product! The product has some sharp
corners which pose a risk of injury!
• Only carry out the steps required for assembly. Never attempt to modify or repair the
product. Do not make any modifications.
• Complete the assembly very carefully, since the product falling off would not only
cause expensive consequential damage but also poses a risk of injury.
• Work on a clean, soft and dry surface. Protect valuable furniture surfaces with a
suitable pad when assembling the product.
• Route cables in such a way that they cannot get jammed or bent.
• Do not overload the product. Observe the “Technical data”.
• In case of doubt, do not install the product yourself; have a professional do it for you.
Assembly
a) Inserting the clips
1
2
• Select the plastic bag with suitable clips.
• Position the clip at an angle at a suitable arm
of the holder.
• Push down the clip from above until it locks
into place.
• Repeat this procedure for attaching the
remaining clips to the other arms of the holder.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the
technical status at the time of printing.
© Copyright 2016 by Conrad Electronic SE.
V2_0116_02-ETS-Mkd
1. Attach the screw clamp to a suitable object.
2. Alternatively, you can remove the lower
screw and screw the arm directly onto a 3/8
thread for use as extension.
3. Adjust the arm and fix the position using the
wing screw.
4. Screw the holder into the arm and fix the
position using the lock nut.
5. Turn, swivel or tilt the holder in the ball joint
and secure the position with the rotatory
handle.
Explanation of symbols:
Adjustment options X
of the component
Turn here to loosen / fix
the adjustment options X
X
X