• Press the WPS button on your WLAN router within 2 minutes. Alternatively you can also
start the WPS function on the web interface of the router.
Please see the operating manual of your router for further details.
• As soon as the configuration is completed, the WIFI/WPS LED stops flashing and remains lit.
• To connect a device via WLAN, select your WLAN with the added identifier. The password
for the WLAN is identical to the WLAN of your router. Alternatively, you can also use the
WPS function (press the button on the repeater for 3 seconds).
Devices can now likewise be connected to the two network ports.
Overview of the modes and access to the web interface
“Repeater” mode
• If you have not carried out the configuration via WPS, proceed after the base configuration
on the web interface with the chapter “Manual configuration for “Repeater””.
• In both cases, connect a computer or a mobile device to the WLAN or one of the two network
ports of the repeater. If the repeater is already configured, the password is identical to that of
your router; otherwise, the WLAN is unencrypted.
• Open your browser and then the configuration page http://ap.setup of the repeater.
If the repeater is not yet configured, its internal DHCP server is still running. In this case,
therefore, you can also call up the configuration page using the standard IP address
192.168.10.1.
If the repeater is already configured and you have problems opening the configuration page,
please restart both your computer and the repeater (unplug and plug in again). Alternatively,
open the web interface using the IP address. Because the repeater is already integrated into
your network, you can see the IP address in your WLAN router. Please see the handbook
for your router for further details.
“Access Point” mode
• If the access point is correctly connected to your router, it is generally already also ready
to use. However, even in this case, you should still carry out the base configuration on the
web interface and the configuration of the WLAN (chapter “Configuration of “Access Point””).
• Connect a computer or a mobile device to the WLAN or the LAN port of the AP.
• Open your browser and then the configuration page http://ap.setup of the AP.
• If the page is not shown, open it using the IP address. Because the access point is already
integrated into your network, you can see the IP address in your WLAN router. Please see
the handbook for your router for further details.
“Router” mode
• Connect a computer or a mobile device to the WLAN or the LAN port of the router.
• Open the configuration page of the router. To do this, enter either the web address http://
ap.setup or the standard IP address 192.168.10.1.
• Because the configuration of “Router” mode occurs in the web interface, again first carry
out the base configuration, then the configuration of the router (chapter “Configuration for
“Router””).
Logging onto the web interface (all modes)
• First select the desired language and wait until the page has reloaded.
• Enter admin as both username and password and log in.
Base configuration on the web interface (all modes)
• As soon as you see the web interface, change the password for the webpage “Password
Settings”. Confirm the new password. If, when you access the web interface, a pop-up for
changing the password is shown, you can also click on OK here.
• Then configure the time zone using “Time Zone Settings”. Activate the NTP option; then
select the time zone and lastly an NTP server. Confirm the selection. After the new registra-
tion, the time is automatically adjusted.
If you have set up the repeater using WPS, the basic configuration is thereby com-
pleted. Naturally, it is then possible to change additional settings.
If you want to open the web interface again after the base configuration, you have
to enter as the login password not the standard password, but rather the new pass-
word you set.
If the device does not function correctly after the configuration, reset it to the factory
settings and try it again.
Configuration for “Access Point”
• After the completion of the base configuration, click on the “AP ...” button at the top left to
start the setup.
• If desired, change the two names of the WLAN networks (2.4 and 5 GHz).
• Now select an encryption for the WLAN. We recommend here that you select the standard
WPA2-PSK, since it offers the highest security. If you have devices that support only WPA,
select both standards.
• Enter a password for the WLAN. It should have min. 8 characters and consist of numbers as
well as upper and lower case letters.
• To finish, click on the button at the lower left to save the selection. As soon as the changes
are saved, the setup is complete.
If you carried out the configuration via WLAN, you must now still connect your device
to the new WLAN network
Configuration for “Router”
• After the completion of the base configuration, click on the “Router …” button at the top left
to start the setup.
• At the top, select the type of your Internet access. If you have e.g. a DSL connection and
access data, select PPPoE here.
• Enter your full username and the password for your DSL connection in the corresponding
fields.
• Then, if desired, change the two names of the WLAN networks (2.4 and 5 GHz).
• Now select an encryption for the WLAN. We recommend here that you select the standard
WPA2-PSK, since it offers the highest security. If you have devices that support only WPA,
select both standards.
• Enter a password for the WLAN. It should have min. 8 characters and consist of numbers as
well as upper and lower case letters.
• To finish, click on the button at the lower left to save the selection. As soon as the changes
are saved, the setup is complete.
If you carried out the configuration via WLAN, you must now still connect your device
to the new WLAN network.
Manual configuration for “Repeater”
• After the completion of the base configuration, click on the “Repeater ...” button at the top
left to start the setup.
• Click in the list to select the WLAN to which you want to connect the repeater or that you
want to amplify. If the WLAN to which you want to connect the repeater is not shown, refresh
the list.
• Now in the open field, enter the password of the WLAN network that you previously selected.
• The names of the WLAN SSIDs are automatically carried over from your router. Then an
identifier is added to the name. However, you can change both names as desired.
• To finish, click on the button at the lower left to save the selection. As soon as the changes
are saved, the setup is complete.
If you carried out the configuration via WLAN, you must now still connect your device
to the new WLAN network.
Positioning of “Repeater”
• When you have finished configuring the repeater, you should position it correctly, as shown
in the following image.
• Try various locations and select the installation location where the best connection to your
existing WLAN router is.
• So that the repeater is not too far from your WLAN router, test the connection e.g. with your
smartphone. If you are connected directly to your router, min. 3 bars of the WLAN display
should be active.
Resetting to Factory Settings
Proceed as follows to reset the product to factory settings.
• Plug the device into a mains outlet and wait until the start-up process has completed.
• Press and hold the countersunk “Reset” (7) for more than 3 seconds. Then release the
button again.
• The product will restart and is then reset to the factory settings. This process takes about
1 to 2 minutes.