Operating instructions
Car holder for iPhone 6, black
Item no. 1366946
Intended use
Use this product to fasten an iPhone 6 to the windshield inside a car. The suction cup
guarantees secure fastening. The product features a flexible support arm for separate
adjustment of the iPhone.
For safety and approval purposes, you must not rebuild and/or modify this product.
If you use the product for purposes other than those described above, the product
may be damaged. Read the instructions carefully and keep them. Make this product
available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All
company names and product names are trademarks of their respective owners. All
rights reserved.
Delivery content
• Car holder
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the
warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may
become dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong
jolts, high humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. Safe operation can no
longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a
low height can damage the product.
• Also observe the safety and operating instructions of any other devices
which are connected to the product.
• Consult an expert when in doubt about operation, safety or connection of
the device.
• Maintenance, modifications and repairs are to be performed exclusively
by an expert or at a qualified shop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.
Operating elements
1
2
3
4
5
6
1 Holding bracket
2 Star grip nut (not depicted)
3 Support arm
4 Suction cup
5 Suction cup tongue
6 Locking lever
Operation
Choose an installation surface that will not impair your visibility of the road
or cause distraction during driving.
Heed all legal restrictions concerning the use of mobile telephones in
vehicles.
• Make sure that the suction cup and the mounting surface are dry and free from
grease and dust.
• Connect the holding bracket to the support arm. The holding bracket must click into
place audibly.
• If necessary, loosen the star grip nut located at the end of the support arm in order
to rotate or swivel the holding bracket. Then retighten the star grip nut.
• Hold the suction cup to the installation surface and apply a little pressure.
• Push the locking lever toward the installation surface so that the suction cup
adheres to the surface. Make sure that the suction cup is well fastened.
• Place your iPhone in the holding bracket. The two rounded corners of the holding
bracket should be on the left side of the iPhone to prevent covering the camera on
the back. The iPhone must click into place audibly.
• Adjust the iPhone to the desired position using the flexible support arm.
• To remove the suction cup from the installation surface, first lift the locking lever and
then pull the suction cup tongue away from the installation surface.
Maintenance and cleaning
Never use any aggressive cleaning agents or chemical solutions.
• Use a slightly damp cloth to clean the suction cup. Use a mild cleaning agent to
clean off tougher dirt. Allow the suction cup to fully dry before returning it to the
installation surface.
• Use a dry, soft and clean cloth to clean the plastic components. You can use a long-
haired, soft and clean brush and a vacuum cleaner to remove dust.
Disposal
At the end of its service life, dispose of the product according to the
relevant statutory regulations.
Technical data
Operating conditions ................................. 0 to +40 ºC, 0 – 80 % RH
Storage conditions..................................... 0 to +40 ºC, 0 – 80 % RH
Suction cup Ø ............................................. 70 mm
Holding bracket dimensions (W x H) ...... 75 x 140 mm
Weight .......................................................... 91 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the
technical status at the time of printing.
© Copyright 2015 by Conrad Electronic SE.
V1_0815_02-ETS-Mkd
