Operating instructions
mSATA hard drive housing USB 3.0, aluminum
Item no. 1346300
Intended use
The hard drive housing is designed to operate a hard disk drive outside a computer
case. An SSD hard disk drive with mSATA connection can be installed in the hard
drive housing. The installed hard disk drive can be operated as an external computer
drive via USB 3.0. The product does not have an external power supply and operates
in "bus-powered mode".
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in
bathrooms, must be avoided under all circumstances.
For safety and approval purposes (CE), you must not rebuild and/or modify this product.
If you use the product for purposes other than those described above, the product may
be damaged. In addition, improper use can cause hazards such as short circuiting,
fire, electric shock etc. Read the instructions carefully and keep them. Make this
product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All
company names and product names are trademarks of their respective owners. All
rights reserved.
Delivery content
• Hard drive housing
• USB 3.0 cable (approx. 23 cm long)
• Cover
• 4 x Screw
• Screwdriver
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the
warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may
become dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong
jolts, high humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. Safe operation can no
longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a
low height can damage the product.
• Also observe the safety and operating instructions of any other devices
which are connected to the product.
• Remove the USB cable from your computer if you are not going to use the
product for a prolonged period of time.
• Only use the product in temperate climates, not in tropical climates.
• Do not place the product near to speakers or machines that give off a
strong magnetic field.
• Only touch the housing on the sides of the hard drive; do not touch the
board with the electronics. Electrostatic discharges may damage the hard
drive.
• When setting up the product, make sure that the cable is not pinched,
kinked or damaged by sharp edges.
• Never use the product immediately after it has been brought from a cold
room into a warm one. The condensation generated could destroy the
product. Allow the product to reach room temperature before connecting
it to the power supply and putting it to use. This may take several hours.
• Use suitable padding to protect the surfaces of valuable furniture against
scratches and dents.
• In schools, educational facilities, hobby and DIY workshops, the product
is to be operated under the responsible supervision of qualified personnel.
• Consult an expert when in doubt about operation, safety or connection of
the device.
• Maintenance, modifications and repairs are to be performed exclusively
by an expert or at a qualified shop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.
Inserting a hard disk drive
1. Slide the installation frame in the inside of the hard drive housing to the side and
out of the housing.
2. Place the SSD hard drive with mSATA connection in the installation frame. Pay
attention to the orientation of the hard disk drive and ensure that the mSATA
connector on the circuit board is inserted correctly into the connections.
3. Slide the installation frame into the housing again. The screw holes of the individual
parts must be flush above each other.
4. Secure the installation frame and housing using the screws included with the
product through the side cover in the housing. Tighten the screws with moderate
force using the screwdriver also included with the product.
We recommend always tightening the hard disk drive to prevent it slipping
out. Be very careful when moving and transporting the hard drive housing if
a hard disk drive is installed but not secured with screws. Without screws,
the installation frame can move or even fall out during sudden movements.
Driver installation
• The necessary drivers are already included in the operating system. A separate
driver is therefore not included with the product.
• Note that a suitable USB 3.0 controller is required for use via USB 3.0. This controller
is built into many modern mainboards, but you can also update your mainboard
using an additional plug-in card.
Operation
• Switch on the computer. Wait until the operating system has fully booted.
• Connect the hard drive housing to an available USB-A port on your computer using
the USB cable. The blue operational LED lights up when the housing is supplied
with power.
• The operating system automatically recognises the product upon first use and
installs the necessary drivers. The drivers are already included in the operating
system.
• The LED indicator flashes when data is being transferred.
The hard disk drive in the hard drive housing is operated without an external
power supply. It operates in "bus-powered mode". This means that the
current provided by the computer via USB (900 mA according to USB 3.0
standard) is sufficient to operate an external hard disk drive.
• To avoid data loss, never disconnect the USB cable from the product when data is
being transferred.
