• The outlet used for the connection must be located in direct proximity to
the device and be easily accessible.
• The power strip is equipped with a child safety lock. Only when the prongs
of a power plug are placed in both openings of a socket at the same time
will the child-lock mechanism release the opening.
Even so, be especially careful if children are around. Children cannot re-
alise the danger arising from the incorrect use of electrical devices. There
is danger to life through an electric shock!
• The product is not a toy and does not belong in the hands of children. Posi-
tion the product so it is out of the reach of children.
• Do not carelessly leave the packaging material lying around since this
may become a dangerous toy for children.
• Handle the product with care; it may be damaged by impacts, blows, or
accidental falls, even from a low height.
b) Installation location
• The product may be used only in dry, enclosed indoor areas only; it must
not get damp or wet! Never set up the product in the direct vicinity of a
bathroom, shower, bathtub or similar. There is danger to life through an
electric shock!
• The product must not be exposed to extreme temperatures, direct sunlight
or strong vibrations.
• Completely unwind the mains cable during use. The power cable must
not be pinched or damaged by contact with sharp edges. Do not place
any objects on the cable, and do not allow it to become kinked. Install the
cable where no one can stumble over it and the plug is easily accessible.
Do not install the mains cable under carpets or the like.
• Do not operate the device in environments where there are high levels of
dust, flammable gases, vapours or solvents. There is a danger of fire and
explosion!
c) Handling and use
• If the mounting clip is used, the power strip must be mounted on a stable
surface.
The strong spring effect can cause pressure points, scratches or discol-
ouration on the surface. Therefore, never attach the power strip to valu-
able surfaces/furniture!
• Never touch, operate, plug in or unplug the product with damp or wet
hands. There is danger to life through an electric shock!
• Never connect the product to the power supply immediately after it has
been transferred from a cold room into a warm one (e.g., during transport).
The condensation that develops in such cases could damage the device
or cause an electric shock! Allow the product to reach room tempera-
ture. Wait until the condensation has evaporated. This might take several
hours. Only after this should the product be plugged into the power supply
and put into use.
• Always pull a mains plug from the mains socket using the gripping sur-
face intended for this purpose. Never unplug the mains plug from a mains
socket by pulling the cable!
• Do not overload the outlet strip. Observe the connected load in the chap-
ter “Technical Data”.
• Do not connect in series! This can lead to an overloading of the outlet
strip! There is a risk of fire!
Plug the earthed mains plug of the outlet strip directly, e.g., into a wall
socket. Do not connect other outlet strips to this outlet strip.
• Do not operate while covered! At higher connected loads, the outlet strip
and the connecting cable become warm, which can lead to overheating
and potentially a fire if covered!
• Current-free only when the plug is withdrawn!
• Do not use the product when it is damaged (e.g., housing or power cable).
There is danger to life through an electric shock!
In this case, dispose of the product in an environmentally correct manner.
It can be assumed that safe operation is no longer possible if:
- the product shows visible signs of damage
- the product does not work at all or works poorly (leaking smoke or a
smell of burning, audible cracking noises, discolouration to the product
or the adjacent surfaces)
- the product was stored under unfavourable conditions
- it was exposed to heavy loads during transport
G
Operating instructions
3-Socket outlet strip with mounting clip
Item no. 1233680
Intended use
The power strip has a total of three outlets to which corresponding loads can be con-
nected.
As a special feature, a broad attachment clip is located on the bottom of the power
strip, so the power strip can be mounted easily on table tops, beams, etc..
The outlet strip should be connected to an earthed mains socket; the mains voltage
should be 230 V/AC, 50 Hz.
The total power consumption of all connected loads must not exceed 3680 W.
The product may only be used in dry, enclosed spaces.
Always observe the safety instructions included in these operating instructions. Read
the operating manual carefully; keep it in a safe place and/or pass it on to other users
of the outlet strip.
Any use other than that described above could lead to damage to this product and
involves risks such as short circuits, fire, electric shock, etc. No part of the product
may be modified or changed!
This product complies with the applicable national and European requirements. All
names of companies and products are the trademarks of the respective owners. All
rights reserved.
Package contents
• Outlet strip
• Operating instructions
Explanation of symbols
The lightning symbol inside a triangle is a warning to inform you of potential
risks of personal injury, such as electric shock.
This symbol indicates specific risks associated with handling, function or
use.
The “arrow” symbol indicates special tips and operating information.
The product is only intended to be installed and used in dry, indoor spaces;
it must not get damp or wet.
Observe the operating instructions!
Safety instructions
Damage due to failure to follow these operating instructions will void the
warranty! We do not assume any liability for any resulting damage!
We do not assume any liability for material and personal damage caused
by improper use or non-compliance with the safety instructions. In such
cases, the warranty will be null and void.
a) General
• The unauthorised conversion and/or modification of the product is not
permitted for safety and approval reasons (CE). Do not open/disassemble!
Contains no customer-serviceable parts.
Maintenance, adjustment or repair work may only be carried out by an ex-
pert/authorised service centre, which is familiar with the hazards involved
and the relevant regulations.
• The product is designed according to protection class I. It may only be
used when connected to an earthed mains socket.