• Connect the appliance to a wall socket that can be accessed easily.
• If the power adapter is damaged, do not touch it; there is danger to life from electric
shock! First, switch off the mains voltage to the mains socket to which the power
adapter is connected (switch off at the corresponding circuit breaker or remove the
safety fuse, then switch off at the corresponding RCD protective switch, so that all
poles of the mains socket are disconnected). You can then unplug the power adapter
from the mains socket. Dispose of the faulty power adapter in an environmentally
friendly way; do not use it any more.
• Consult an expert when in doubt about operation, safety or connection of the device.
• Maintenance, modifications and repairs are to be performed exclusively by an
expert or at a qualified shop.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
Connection
• Make sure there is a clearance of at least 50 mm between the LED power adapter and other
objects/surfaces when installing the product.
• Connect the plug of the LED light with the low-voltage output jack of the LED power adapter. The
length of the cable from the LED light to the LED power adapter must not exceed 2m.
• Connect the LED power adapter to a standard household power socket.
• Finally, make sure the LED power adapter is correctly connected.
Maintenance and cleaning
• This product does not require maintenance. There are no components located inside the product
you need to maintain. Never open/dismantle the product. Have maintenance and repairs done
by qualified experts or repair shops only.
• Disconnect the product from the power supply before cleaning. To clean the product, a dry,
soft and clean cloth is sufficient. You can use a long-haired, soft and clean brush and a vacuum
cleaner to remove dust.
• Never use any aggressive cleaning agents or chemical solutions as they may cause damage to
the housing or the product to malfunction.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household
waste.
At the end of its service life, dispose of the product according to the relevant statutory
regulations.
You thus fulfil your statutory obligations and contribute to the protection of the
environment.
Technical data
Item no.
1217845
1217846
Input
200 – 240 V/AC, 50/60 Hz
Output voltage
12 V/DC
8.5 – 22.5 V/DC
Output current
max. 670 mA
350 mA
Rated power
8 W
No-load output voltage
max. 13 V/DC
max. 30 V/DC
Power factor value
0.8
Protection class
II
Housing temperature (max.)
+75 ºC (tc)
Operating conditions
0 to +40 ºC (ta), 10 – 85 % RH
Storage conditions
-20 to +50 ºC, 10 – 95 % RH
Dimensions (W x H x D)
72 x 63 x 20 mm
Weight
approx. 42 g
72 mm
63 mm
20 mm
Operating instructions
LED power adapter
Item no. 1217845
Item no. 1217846
Intended use
The LED power adapter is specially designed as a power supply for LED lighting. The product is
protected against short-circuiting, overload and overheating.
Item no. 1217845: suitable for LED applications with 12 V/DC operating voltage
Item no. 1217846: supplies constant output current of 350 mA
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you
use the product for purposes other than those described above, the product may be damaged. In
addition, improper use can cause hazards such as short circuiting, fire, electric shock etc. Read
the instructions carefully and keep them. Make this product available to third parties only together
with its operating instructions.
This product complies with the statutory national and European requirements. All company names
and product names are trademarks of their respective owners. All rights reserved.
Delivery content
• LED power adapter
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on proper
handling in this manual, we assume no liability for any resulting personal injury or
damage to property. Such cases will invalidate the warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become
dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed if
the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
• Only install and use the product indoors in dry and closed rooms. The product must
not get damp or wet, as such conditions constitute a risk of electric shock!
• Make sure that the total power of the connected LED lighting does not exceed the
product‘s max. output power (see Technical Data).
• Operate the product only under the specified temperature conditions (see Technical
Data). Do not exceed the maximum ambient temperature (ta).
• Never immerse the product into water or other liquids.
• Make sure there is sufficient clearance between the product and other objects.
• Only connect the power adapter to a normal mains socket connected to the public
supply. Before plugging in the power adapter, check whether the voltage stated on
the power adapter complies with the voltage of your electricity supplier.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the
technical status at the time of printing.
© Copyright 2014 by Conrad Electronic SE.
V1_0914_02-KV
