Operating elements
Fast
Medium
Slow
Off
1 Lock screw
2 Front protective grille
3 Cap nut
4 Fan blade
5 Retainer for rear protective grille
6 Rear protective grille
7 Rotor shaft
8 Motor housing
9 Oscillation switch
10 Switch 0–1–2–3
(Off–Slow–Medium–Fast)
11 Mains cable with mains plug
12 Column
13 Stand
14 Column retainer
Operation
a) Installation
• Remove all packaging material and place all components on a clean, flat surface,
e.g. a table.
• Turn the retainer (14) anticlockwise to remove it from the column (12) of the motor
assembly.
• Insert the column of the motor assembly into the opening on top of the stand (13).
Hold the motor assembly upside down in order for the stand to move all the way
against the column.
• Manually turn the retainer underneath the stand onto the thread of the column in
clockwise direction. Make sure the connection between the column and stand is
hand-tight and secure.
• Place the motor assembly including the stand on a stable surface.
• Turn the cap nut (3) clockwise to remove it from the rotor shaft (7).
• Turn the retainer (5) anticlockwise to remove it from the thread of the motor
assembly.
• Place the rear protective grille (6) onto the motor assembly with the lobes
interlocking with the upper openings and lower opening of the protective grille and
thereby keeping the protective grille in place. The handle on the rear protective
grille must face upwards.
• Turn the retainer (5) onto the thread of the motor assembly in clockwise direction to
secure the protective grille.
• The rear protective grille consists of two parts that are connected to each other
with Phillips head screws. Check the Phillips head screws of the rear protective
grille for tightness.
• Place the fan blade (4) onto the rotor shaft (7). Please note that the thread on one
side of the rotor shaft is levelled and that the opening in the fan blade must be fitted
precisely. The two pins on the rear side of the rotor shaft must be aligned with the
notches behind the fan blade.
• Turn the cap nut (3) onto the thread of the rotor shaft in anticlockwise direction in
order to secure the fan blade. Hold the fan blade with one hand to tighten the cap
nut. Tighten the cap nut by hand only.
Risk of injury! The fan blade edges are very sharp.
• Attach the front protective grille to the rear protective grille using six Phillips head
screws. Use a Phillips screwdriver to tighten all screws evenly.
b) Installation location
Carry the product at the handle located on the rear protective grille (6). Place the
product with the stand (13) onto a dry, clean, level and stable surface.
Keep sufficient distance to appliances generating heat.
Do not place the product below vases or flowerpots in order to prevent the
product from getting into contact with water.
c) Turning on/off, adjusting fan speed and oscillation settings
• Make sure the switch 0–1–2–3 (10) is at position 0. Connect the mains plug (11) to
a wall socket.
• Turn the switch 0–1–2–3 to position 1. The fan starts rotating at low speed. Turn
the switch 0–1–2–3 to position 2. The fan starts rotating at medium speed. Turn the
switch 0–1–2–3 to position 3. The fan starts rotating at high speed.
• Change the airflow direction by carefully tilting the motor housing (8) up or down.
Let the motor housing lock into place at the desired position. Do not apply too much
force when adjusting the motor housing. Tilt the motor housing only as far as it goes.
• Press down the oscillation switch (9). The fan starts rotating to the left and right
alternately. Fully pull up the oscillation switch in order to stop the oscillating function.
• Turn the switch 0–1–2–3 to position 0 to switch off the fan.
Maintenance and cleaning
a) General
• Switch off the product and disconnect the mains plug from the wall socket before
cleaning.
• Cleaning and servicing must not be carried out by children.
• Do not use any abrasive or chemical cleaners.
• Frequently wipe the components of the fan including the protective grilles and stand
with a dry dust rag.
• When not using the product for a longer period of time, cover it and store it at a dry
location protected from direct sunlight.
b) Cleaning the fan blade and protective grilles
• If the fan blade is heavily stained by dust, you may disassemble the product following
the instructions in chapter “Installation” in reverse order.
• Clean the rear and front protective grilles as well as the fan blade with a slightly
damp cloth.
Risk of injury! The fan blade edges are very sharp.
• Thoroughly dry all components after cleaning and before reinstalling.
• Assemble the product as described in chapter “Installation”.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste.
At the end of its service life, dispose of the product according to the
relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of the
environment.
Technical data
Power supply .......................................220 - 240 V/AC, 50 Hz
Power consumption............................45 W
Protection class ..................................II
Oscillation range .................................approx. 85 °
Operating temperature.......................5 to +35 °C
Operating humidity..............................30 – 90 % RH
Storage temperature ..........................5 to +40 °C
Storage humidity .................................
<
90 % RH
Grille diameter .....................................approx. 30 cm
Dimensions (W x H x D)......................27 x 42 x 33 cm
Weight ...................................................approx. 3.2 kg
These operating instructions are published by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved.
© Copyright 2014 by Conrad Electronic SE.
V2_0314_02-HK
