manualshive.com logo in svg

Renishaw TONiC T103x RKLC20-S, Руководство по установке, Страница: 5 / 25

Поделиться
Скачать
Renishaw TONiC T103x RKLC20-S Скачать руководство пользователя страница 5

TONiC RKLC20-S linear installation guide

3

TONiC T103x readhead installation drawing

Forward direction of 

readhead relative to scale

R >  20 Dynamic bend radius

 

 

R >  10 Static bend radius

Ø 4.25 ±

0.25

  

Set-up LED

Optical centreline marker

A

0.6

35

23

11.5

6 min

18

7.8

Reference mark selector 

sensor position

P and Q limit switch 
sensor position

Selected IN-TRAC 

™  

reference mark

0.08

(Roll tol. ±0.5°)

13.5

11*

4.15

10

8.75 *

Offset 3.75 ±0.5

0.25

29

Detail A

Scale reading surface

4.75

†

Recommended 
mounting faces

Scale thickness 0.15 

(including adhesive)

P limit magnet

Reference mark 
selector  magnet  

Q limit magnet

(Yaw tol. ±0.4°)

Rideheight: 2.1 ±0.15

(Pitch tol. ±1°)

2 off mounting holes M2.5 through, counterbored 

Ø3 × 2.3 deep both sides.

NOTE: 

The recommended thread engagement 

is 5 min (7.5 including counterbore) and the 
recommended tightening torque is between 0.25 

and 0.4 Nm.

3

16

4.25

22

Optical centreline 

(incremental and reference mark)

CAL  /AGC  LED

31

2 off holes M2.5 through, 

counterbored Ø3 × 2.75 deep 

from alternative mounting face

3

Alternative 

mounting faces

* 

Extent of mounting faces. 

†

 

Dimension from substrate surface.

Dimensions and tolerances in mm

7.8

Содержание TONiC T103x RKLC20-S


























Отзывы:

Нет отзывов