manualshive.com logo in svg

Renishaw MCU1, Руководство пользователя, Страница: 22 / 31

Поделиться
Скачать
Renishaw MCU1 Скачать руководство пользователя страница 22

CMM

 

auto

 

mode

 

(MCU1

 

and

 

MCU5

 

only)

 

 

This mode is not selectable via the ‘MODE’ button, but is automatically invoked whenever the UCC is 

placed into ‘DCC mode’ (automatic mode). 

NOTE:

  When the MCU

lite-2

 is in this mode the MCU status LED is amber and changes to 

green when a ‘Joystick enable’ button is pressed. 

NOTE:

  DCC mode is indicated on the LCD (refer to section 4.3).  For the MCUlite-2 it is 

indicated by the MCU status LED being RED. 

Head

 

mode

 

 

Provides the user with control over the Renishaw PH10, PH20 or REVO heads. 

In this mode the joystick will move either of the motorised head axis. The LCD display will indicate the 

angle of the two-head rotation axis. For the PH10 the joystick fast/slow button will give jog operation if 

not pressed or fast sweep operation if pressed.  For the REVO the fast / slow button will control the 

speed.  If no head is fitted then the LCD screen will display ‘None’. 

NOTE: However, to ensure correct operation, the head type must be set correctly within the 

configuration.ini file. 

With the REVO or PH20 head there is an additional facility of ‘SNAP ON’.  The use of ‘SNAP ON’ is 

controlled by the use of the left / right axis lock button, repeated pressing will toggle the facility on and 

off.  ‘SNAP ON’ is displayed in text on the LCD display when it is selected.  When ‘SNAP ON’ is 

selected the up / down and twist operation of the joystick will move the REVO or PH20 ‘A’ and ‘B’ 

axes normally, but after about 1 second of the joystick being returned to its null position the head will 

automatically move to the nearest multiple of the snap angle. 

The snap angle is configurable via the configuration file. The maximum snap angle is 7.5° and the 

minimum is 0.05°. 

Rotary

 

table

 

mode

 

(MCU1

 

and

 

MCU5

 

only)

 

This mode provides the user with control over a rotary table if it is connected to the system. Twisting 

the joystick will cause rotary table movement. The joystick fast/slow button will control fast (pressed) 

or slow (not pressed) operation. The LCD display will indicate its angle of rotation. 

  

Page 22 of 31

MCU1, MCUlite-2 and MCU5 user's guide

02/01/2013

file://C:\TEMP\~hhC0D2.htm

Содержание MCU1
































Отзывы:

Нет отзывов