background image

 

User's  Manual 

R20UT0583EJ0200    Rev.2.00 

 

Page 1 of 8   

Mar 05, 2014 

 

R0E55630EDMB00 

Debugging MCU Board for 144-pin 0.5mm-pitch LQFP 

of the RX630 Group 

1.  Overview 

This product is for MCUs of the RX630 group in the PLQP0144KA-A package.   
With the E20 emulator, the emulator occupies some user port pins for controlling the emulator and output of trace 

information. These user port pins must be connected with a 38-pin connector installed on the user system.   
With the debugging MCU board, however, all user port pins are available for the user system. In addition, you do not 

need to install a 38-pin connector on the user system.   
Figure 1 shows the configuration of a system that includes the debugging MCU board and the E20.   
Be sure to read section 7, Notes on Usage, before using the debugging MCU board. 

Debugging MCU board

(this product)

YQPACK

(provided with this 

product)

NQPACK

(provided with this product)

E20 emulator

User system

38-pin connector

Host computer

USB interface cable

 

Figure 1      System Configuration   

2.  Components 

Table 1 lists the components of the debugging MCU board. Check that you have all of the components when you 

unpack the box. 
Table 1      Components of the Debugging MCU Board 
Component 

Quantity 

Remarks 

Debugging MCU board common part 

(R0E55630EVKZ00) 

For the dimensions, refer to section 6, Dimensions of the 

Debugging MCU Board. 

Converter board (R0E55630EPFK00) 

For the dimensions, refer to section 6, Dimensions of the 

Debugging MCU Board. 

YQPACK144SD   

(from Tokyo Eletech Corporation) 

Connector to be placed between the debugging MCU board 

and the NQPACK. 

NQPACK144SD-ND   

(from Tokyo Eletech Corporation) 

IC socket for mounting on the user system 

YQ-GUIDE-S1   

(from Tokyo Eletech Corporation) 

Screws for fastening the YQPACK to the NQPACK. 

Cautions in handling

 

Cautions when handling the products of Tokyo Eletech 

Corporation

 

User’s Manual (English and Japanese) 

1 for each 

This manual (English) 

Note:    NQPACK, YQPACK, YQSOCKET, YQ-GUIDE, HQPACK, TQPACK, TQSOCKET, CSSOCKET, 

CSPLUG/W, and LSPACK are trademarks of Tokyo Eletech Corporation. 

R20UT0583EJ0200 

Rev.2.00 

Mar 05, 2014 

Содержание R0E55630EDMB00









Отзывы: