Renesas Emulation Pod M306H7T3-RPD-E страница 84 Скачать руководство пользователя

Страница: 84 / 90

M306H7T3-RPD-E User’s Manual

5. Troubleshooting

REJ10J0964-0100 Rev.1.00 August 01, 2005

Page 82 of 88

(2) Program Window is Not Displayed at Debugger Startup (User System Connected)

Table 5.2 Checkpoints of errors when starting up the emulator debugger (user system connected)

Error Checkpoint

ERROR 16005:

Can't connect with the target.

(1) Check the connection between the PC4701 and host machine.

See the PC4701 User's Manual.

(2) Check that the PC4701 is powered on.

See the PC4701 User's Manual.

(3) Check that all switch settings on the rear of the PC4701 and

interface cable settings of the emulator debugger match.

See the PC4701 User's Manual and the emulator debugger user's
manual (online manual).

ERROR 16211:

The version of the emulator and the
firmware on the target are not same.

(1) Check the connection between the PC4701 and this product.

See “2.4 Connecting the PC4701” (page 23)

(2) Download the proper firmware.

See "2.6 Downloading Firmware" (page 28).

(3) Choose the proper MCU file in the Init dialog box.

See the emulator debugger user's manual (online manual).

(4) Check that the descriptions in the MCU file are correct.

See "3.1 Making an MCU File" (page 48).

ERROR 16215:

Cannot communicate with the debugging
monitor. Execute the RESET command.

(1) Check the connection between the PC4701 and this product.

See “2.4 Connecting the PC4701” (page 23)

(2) Check that the reset pin of the user system is at “H” level.

See the MCU specifications.

(3) Check that CNVSS is held low.

See the MCU specifications

(4) Check that the oscillator circuit of the emulation pod is oscillating

properly.

See "2.9.3 Selecting Clock Supply" (page 38)

ERROR 16014:

Communication ERROR.
Can't accept data.

(1) Check that the oscillator circuit of the user system is oscillating

properly.

See "2.9.3 Selecting Clock Supply" (page 38).

(2) Check that the PC4701 LEDs at startup show normal operation.

See "2.5.3 LED Display When the Emulator Starts Up Normally"
(page 27).

ERROR 16231:

There was sent undefined data from the
emulator.

Check that the emulator debugger has not been started up without
shutting down the PC4701.

See "4.5 IMPORTANT: Note on Quitting the Emulator Debugger"
(page 76).

Содержание Emulation Pod M306H7T3-RPD-E



























































































Результаты поиска

Содержание Emulation Pod M306H7T3-RPD-E

Отзывы:

Похожие инструкции для Emulation Pod M306H7T3-RPD-E

Бренды по названию

Популярные бренды

Renesas Emulation Pod M306H7T3-RPD-E, Руководство пользователя

Результаты поиска

Содержание Emulation Pod M306H7T3-RPD-E

Отзывы:

Похожие инструкции для Emulation Pod M306H7T3-RPD-E

Бренды по названию

Популярные бренды