manualshive.com logo in svg

Renesas 89HPES24T3G2ZBAL, Руководство пользователя

"Пользовательский мануал для продукта Renesas 89HPES24T3G2ZBAL доступен для бесплатного скачивания на нашем веб-сайте. Этот мануал предоставляет подробные инструкции по использованию продукта и его функциональным возможностям. Скачайте его сейчас на manualshive.com и начните пользоваться вашим продуктом с максимальной эффективностью."

Поделиться
Скачать
background image

IDT   Link Operation

PES24T3G2 User Manual

3 - 4

February 22, 2012

Notes

The PES24T3G2 does not initiate autonomous link width upconfiguration and downconfiguration of

links, except for downconfiguration due to link reliability reasons. Therefore, the Hardware Autonomous
Width Disable (HAWD) bit in the port’s PCIELCTL register has no effect and is hardwired to 0x0. Addition-
ally, the PES24T3G2 port’s never set the ‘Autonomous Change’ bit in the training sets exchanged with the
link partner during link training. A Downstream port link partner may autonomously change link width. When
this occurs, the PES24T3G2 downstream port sets the Link Autonomous Bandwidth Status (LABWSTS) bit
in the PCIELSTS register.

Link Speed Negotiation

The PCIe 2.0 specification introduces support for 5.0 Gbps data rates per lane (Gen2), in addition to the

2.5 Gbps data rates (Gen1) mandated in previous versions of the specification. Per the PCIe 2.0 specifica-
tion, all lanes of a link must operate at the same data rate. During full link training, links initially operate at
2.5 Gbps. Once the LTSSM on both components of the link reaches the L0 state, the link speed may be
upgraded to 5.0 Gbps if this capability is advertised and desired by both components. The process of
upgrading the link speed does not result in a DL_Down state. 

It is the responsibility of the upstream component of the link (i.e., switch downstream ports) to keep the

link at the target link speed or at the highest common speed supported by both components of the link. In
addition, either link component may request a link speed change due to software requests or link reliability
reasons (i.e., speed downgrade). Downstream components are further permitted to request link speed
changes due to autonomous hardware initiated mechanisms. 

A component must only initiate a link speed change when it knows that its link partner supports the

target speed via prior exchange of Training Sets. As stated before, Gen2 support is optional while Gen1
support is mandatory. Also, a component may advertise supported link speeds via the Recovery state,
without necessarily changing the link speed.

If neither component in the link advertises support for Gen2, then the link remains operating in Gen1

speed. If one of the components decides to advertise support for Gen2 (i.e., software sets the Target link
Speed = Gen2), then this component will advertise its support for Gen2 speed via the Recovery state. The
link will continue to operate in Gen1 speed since only one of the components has advertised support for the
higher speed. If one component has advertised support for Gen1 and Gen2, and the other has advertised
support for Gen1 only, then the link will remain operating in Gen1 speed until the lesser-speed component
decides to:

–

Advertise support for Gen2 via the Recovery state without modifying the link speed. The link
remains operating at Gen1 speed.

–

Transition the link speed to Gen2 via the Recovery.Speed state. The link will operate at Gen2
speed. In this case, the advertisement of Gen2 speed by both components is done implicitly in the
Recovery substates entered while modifying the link speed. 

Link Speed Negotiation in the PES24T3G2 

The PES24T3G2 ports support per lane data rates of 5.0 Gbps and 2.5 Gbps. The highest data rate of

each link is determined dynamically, and depends on the following factors:

–

Maximum link data rate supported by both components of the link

–

The Target Link Speed set via the Link Control 2 Register (PCIELCTL2)

–

The Hardware Autonomous Speed Disable (HASD) bit in the PCIELCTL2 register

–

The reliability of the link at 5.0 Gbps

By default, the Target Link Speed (TLS) of each port is set to 5.0 Gbps. Therefore, the PES24T3G2

ports advertise support for 5.0 Gbps during the link training process via training-sets. After a fundamental
reset, each port link trains to the L0 state at 2.5 Gbps. If the Target Link Speed indicates 5.0 Gbps (default
value), the PHY LTSSM automatically initiates link speed upgrade to 5.0 Gbps using the link speed change
mechanism described in the PCIe 2.0 specification. This occurs regardless of the setting of the Hardware

Autonomous Speed Disable (HASD) bit in the PCIELCTL2 register.

1

Содержание 89HPES24T3G2ZBAL






































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 89HPES24T3G2ZBAL

GAIM Compact Troubleshooting preview
Compact
Бренд: GAIM Страницы: 2
Eaton NR Installation And Operation Instructions Manual preview
NR
Бренд: Eaton Страницы: 12
Dahua D-PFS4226-24ET-240 Web Operation Manual preview
D-PFS4226-24ET-240
Бренд: Dahua Страницы: 58
Daxten SCOUTCOMBO - Installation Manual preview
SCOUTCOMBO -
Бренд: Daxten Страницы: 7
Qlogic SANbox 5000 Series Quick Start Manual preview
SANbox 5000 Series
Бренд: Qlogic Страницы: 8
Panio HW2250K User Manual preview
HW2250K
Бренд: Panio Страницы: 5
Kramer VP-727XL User Manual preview
VP-727XL
Бренд: Kramer Страницы: 61
Edge-Core AS7326-56X Quick Start Manual preview
AS7326-56X
Бренд: Edge-Core Страницы: 9
West Mountain Radio PWRguard PLUS Operating Manual preview
PWRguard PLUS
Бренд: West Mountain Radio Страницы: 10
Hewlett Packard Enterprise FlexFabric 5940 Series Configuration Manual preview
FlexFabric 5940 Series
Бренд: Hewlett Packard Enterprise Страницы: 123
Lockly PGH222 User Manual preview
PGH222
Бренд: Lockly Страницы: 12
Manhattan 522908 User Manual preview
522908
Бренд: Manhattan Страницы: 4
Zektor HD800-V2 User Manual preview
HD800-V2
Бренд: Zektor Страницы: 41
Sven HB-012 User Manual preview
HB-012
Бренд: Sven Страницы: 4
QTech QSW-4600 Series Hardware Installation And Reference Manual preview
QSW-4600 Series
Бренд: QTech Страницы: 58
Eaton Moeller IZM Series Quick Start Manual preview
Moeller IZM Series
Бренд: Eaton Страницы: 4
Avenview SW-HBT-C6POE-16X16E Manual preview
SW-HBT-C6POE-16X16E
Бренд: Avenview Страницы: 19
VNS S901 Quick User Manual preview
S901
Бренд: VNS Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды