Remington 494 Скачать руководство пользователя | Manualshive

Страница: 11 / 24

background image

11

101437

482-59

G 018

Safety Precautions

6.

Power fasteners are a permanently installed fixture. An act of demolition is required for their
removal. Appropriate safety precautions must be taken.

Plastic Flute

Shank

Head

482-60

7.

NEVER use common nails or other materials as fasteners. Remington Power Fasteners are
manufactured from special steel and heat treated to produce a very hard yet ductile fastener.

G 018

8.

NEVER pry a power load out of the tool. Prying can discharge the load causing serious injury
(see

Troubleshooting Guide, page 16).

9.

ALWAYS insert the power fastener first, then the power load. If work is interrupted for any
reason, ALWAYS remove the power load before removing the power fastener (see page 15,
item 7).

«
...
9
10
11
12
13
...
»

Содержание 494

























Отзывы:

Нет отзывов

Похожие инструкции для 494

Бренд: Laser Страницы: 8

Бренд: Palmgren Страницы: 12

Бренд: Samson Страницы: 16

Бренд: Balcrank Страницы: 8

Бренд: Wacker Neuson Страницы: 48

Бренд: BGS technic Страницы: 9

Бренд: Mannesmann Demag Страницы: 16

Бренд: Parkside Страницы: 138

Бренд: Silverline Страницы: 2

Бренд: Eaton Страницы: 6

Бренд: Gardner Denver Страницы: 27

Бренд: Xantrex Страницы: 30

Бренд: YATO Страницы: 88

Бренд: Echo Страницы: 24

Бренд: Palmgren Страницы: 46

Бренд: KNOVA Страницы: 40

Бренд: RocketFish Страницы: 16

Бренд: SOLDER PEAK Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды