Remington 100271-01 Скачать руководство пользователя страница 6

Страница: 6 / 16

100273

WARNING ICON

G 001

WARNING

Cutting edges on chain are sharp. Use protective
gloves when handling chain.

Figure 3 - Assembling Guide Bar, Chain, and Hand Guard

Adjusting
Block

Adjusting
Screw

Sprocket
Support

Adjusting
Plate

Figure 4 - Part Locations for Assembling Guide Bar

ASSEMBLY

UNPACKING

Remove all items from carton.

Check all items for any shipping damage. If you find any
damage or if any parts are missing, promptly inform
dealer where you bought chain saw.

IMPORTANT

Do not clamp chain saw in vise during assembly.

Lay chain out flat.

Remove guide bar nuts from guide bar bolts (see Figure 3).

Turn adjusting screw counterclockwise (see Figure 4).
Continue to turn adjusting screw until adjusting block is to
rear of adjusting plate.

Install guide bar onto saw body. Place rear of guide bar
between adjusting plate and sprocket support.

IMPORTANT:

Make sure to insert adjusting block into

oval adjusting hole on guide bar.

Attach guide bar nuts to guide bar bolts.

IMPORTANT:

Tighten guide bar nuts finger tight only. Make sure
adjusting block is in oval adjusting hole on guide bar.

Place chain around drive sprocket, then along top groove
of guide bar and around guide bar nose.

Note:

Make sure

cutting edges of chain are facing the right direction.
Position chain so cutting edges on top of guide bar face
guide bar nose (see Figure 3).

WARNING ICON

G 001

CAUTION

Do not place chain on saw backwards. If chain is
backwards, saw will vibrate badly and will not cut.

Adjust saw chain tension. Follow steps under Saw
Chain Tension Adjustment, page 7.

If saw has 2-piece side cover, attach sprocket cover.

Drive
Sprocket

Guide Bar
Bolts

Saw
Chain

Guide
Bar

Adjusting
Hole

Guide Bar
Nuts

Cutting
Edge

Towards
Guide
Bar Nose

Sprocket
Support

Содержание 100271-01

















Результаты поиска

Содержание 100271-01

Отзывы:

Похожие инструкции для 100271-01

Бренды по названию

Популярные бренды

Remington 100271-01, Руководство пользователя

Результаты поиска

Содержание 100271-01

Отзывы:

Похожие инструкции для 100271-01

Бренды по названию

Популярные бренды