REMEHA Gas 320 Ace 285 Скачать руководство пользователя

Страница: 17 / 96

4.5

Requirements on the flue gas discharge system

4.5.1

Classification

Important

The installer is responsible ensuring that the right type of flue

gas outlet system is used and that the diameter and length are

correct.

Always use connection materials, roof terminal and/or outside

wall terminal supplied by the same manufacturer. Consult the

manufacturer for compatibility details.

The use of flue gas outlet systems from other manufacturers is

allowed in addition to the recommended manufacturers listed in

this manual. Use is only allowed when all our requirements are

met and the description of flue gas connection C

is respected.

Tab.5

Type of flue gas connection: B

- B

23P

Principle

Description

Recommended manufactur

ers

(1)

AD-3001055-01

Room-ventilated version

Without down-draught diverter.

Flue gas discharge via the roof.

Air from the installation area.

The air supply opening of the boiler must stay open.

The installation area must be vented to ensure sufficient air

supply. The vents must not be obstructed or shut off.

The IP rating of the boiler is lowered to IP20.

Connection material and roof

terminal:

Alukan

Cox Geelen

Muelink & Grol

(1) The material must also satisfy the material property requirements from the relevant chapter.

Tab.6

Type of flue gas connection: C

Principle

Description

Recommended manufactur

ers

(1)

AD-3001057-01

Room-sealed version

Flue gas discharge via the roof.

Air supply opening is in the same pressure zone as the dis

charge (e.g. a concentric roof terminal).

Roof terminal and connection

material

Remeha, combined with con

nection material from Muelink

& Grol

Remeha 350/350, in combi

nation with connection mate

rial from Alukan (Only for

Remeha Gas 620 Ace)

Cox Geelen

Muelink & Grol

(1) The material must also satisfy the material property requirements from the relevant chapter.

4 Before installation

7734324 - v.03 - 29092020

Содержание Gas 320 Ace 285

































































































Результаты поиска

Содержание Gas 320 Ace 285

Отзывы:

Похожие инструкции для Gas 320 Ace 285

Бренды по названию

Популярные бренды

REMEHA Gas 320 Ace 285, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Gas 320 Ace 285

Отзывы:

Похожие инструкции для Gas 320 Ace 285

Бренды по названию

Популярные бренды