Reloop RP1000M, Инструкция по эксплуатации

Страница: 10 / 16

10
ENGLISH
SETTING UP & CONNECTIONS
1. Mount the Turntable -1- onto the motor. To do so, place the Turntable above the Turntable Hub -3-.
2. Pull the belt to the lower side of the Turntable over the Drive Hub -2-.
3. Place the supplied slipmat above the Turntable Hub -3- and onto the Turntable.
4. Place the Balancing Weight -16- onto the Pick-Up Arm -11-.
NOTE! The Balancing Weight Scale -15- must face toward the DJ.
5. Screw the Headshell with Pick-Up System -10- into the Pick-Up Arm -11-. The pick-up system is easy to exchange, if required:
a) First loosen the fastening screw on the headshell and disconnect the cable of the supplied pick-up system.
b) Remove the old pick-up system from the headshell.
c) Now connect the leads of the pick-up system and observe the assignment of wires:
d) Tighten the fastening screws to the headshell.
6. Connect the Audio Output Cable -17- to the phono inputs of your mixer. Connect the GND Grounding Cable -18- to the grounding screw of your
mixer.
7. If required, connect a remote control to the Connection for Remote Control -19-.
8. Connect the mains line to Mains Connection -20- and an outlet.
OPERATION
1. Balancing Weight
Bring the Pick-Up Lift -13- to the „DOWN“ position. Guide the Pick-Up Arm -11- just in front of the Turntable -1-. Adjust the Balancing Weight -16- by
turning it clockwise as such that the Pick-Up Arm -11- does not lean up nor down, i.e. it should be balanced parallel to the record. Then return the
Pick-Up Arm -11- to its rest -12-. Set the Balancing Weight Scale -15- as such that the „0“ position is above the marked line. Continue turning the
balancing weight clockwise until the scale indicates the value which corresponds to the recommended stylus force of the pick-up system.
2. Anti-Skating Wheel
Adjust the Anti-Skating Wheel -14- as such that the value of the stylus force corresponds to the stylus force of the pick-up system.
3. Power ON
After carrying out all connections turn on the device via the ON/OFF Switch -5-; the turntable‘s illumination is activated.
4. Play
Place a record onto the slipmat on the Turntable -1-. Use the 33/45 Selectors -7- to set the correct speed. The LED of the respective selector illu-
minates. Activate the START/STOP Button -6-. Remove the headshell with the Pick-Up System -10-. Now bring the Pick-Up Lift -13- into the “UP”
position and move the Pick-Up Arm -11- just above the desired position of the record. Then bring the Pick-Up Lift -13- “Down” so that the Pick-Up
Arm -11- lowers into the vinyl groove.
NOTE! It is possible to leave the Pick-Up Lift permanently in a “Down” position and to lower the Pick-Up Arm manually onto the desired posi-
tion. When doing so, be sure not to damage the stylus of the Pick-Up System.
5. Stylus Illumination
Use the corresponding Switch -8- to activate the stylus illumination, if required, to be able to see the groove of the vinyl more clearly. Deactivate
the stylus illumination by pressing the lamp down until it locks into place.
6. RPM Fine-Tuning
Use the Pitch Fader -9- to steplessly adjust the speed of the record. If you wish to play the vinyl in original speed, bring the Pitch Fader to position
„+/- 0%“.
TECHNICAL SPECIFICATIONS
Model: ................................................ 2 speeds, fully manual
Drive: ................................................. belt drive
RPM: .................................................. 33 1/3 and 45 RPM.
Start/Stop time: .............................. < 1 sec.
Starting torque: ............................... ~ 1000 g/cm
Flutter: .............................................. < 0.25% WRMS
Dimensions: ...................................... 450 x 352 x 144 mm
Weight: .............................................. 5.7 kg
Reloop
Global Distribution GmbH, Schuckertstr. 28, 48153 Muenster / Germany
Fax: +49-251.6099368
Subject to alterations.
Illustrations similar to original product.
Misprints excepted.
Colour: Channel and Polarity:
White (L+) left, plus terminal
Blue (L-) left, minus terminal
Red (R+) right, plus terminal
Green (R-) right, minus terminal