Reliable N2-Blast DDX, Инструкции по установке, эксплуатации, уходу и обслуживанию, Страница: 21 / 26

FPS-900-RS Nitrogen Generator
General
This manual provides instruction for the proper use and
maintenance of South-Tek Systems N2-Blast
® FPS-900-
RS. South-Tek Systems and Reliable are not responsible
for damages when using this in manners not approved by
South-Tek Systems and Reliable. The user(s) of this docu-
ment should confer any questions with a qualified South-
Tek Systems representative on its commissioning and
correct use. Please contact South-Tek Systems with any
question or concerns at:
South-Tek Systems, LLC
2940 Orville Wright Way Ste 600
Wilmington, NC, 28405
Tel: (888) 526-6284
Email: Info@southteksystems.com
http://www.southteksystems.com/
Important Information
All personnel (and their supervisors) installing, operating,
and maintaining the N2-Blast
® must read and fully under-
stand this manual prior to installing, operating or perform-
ing maintenance. The N2-Blast
® produces nitrogen (N
2
) at
a low flow rate, which quickly dissipates into the air. N
2
gas
is not poisonous, but do not directly inhale since high
concentrations can cause asphyxiation. Install the unit in
a well-ventilated room that is not sealed off from normal
living space air changes. All personnel involved with the
installation, operations, and maintenance of the N2-Blast
®
must follow safe working practices, including OSHA and
local health/safety code regulations.
Safety Guidelines
The following section outlines the basic safety consid-
erations about installation and operation of the N2-Blast ®
FPS-900-RS. For other equipment used with the nitrogen
generator, such as external air compressors, and dryers,
refer to the manufacturer’s safety guidelines.
Using the N2-Blast ® FPS-900-RS correctly is impor-
tant for safety and trouble-free operation. Wrong use can
cause damages to the system or can lead to incorrect gas
supply. The nitrogen generator produces nitrogen at a low
flow rate, which quickly dissipates into the air. Nitrogen
is not poisonous, but do not directly inhaled, since high
concentrations, can cause asphyxiation. Install the unit
in a well-ventilated room, unsealed off from normal living
space air changes.
Warning:
Install the unit in a within a well-ventilated room,
one that is not sealed off from normal living space air
changes.
Read carefully and act accordingly before operating
or repairing the unit:
• The operator must use safe working practices and
rules when running the nitrogen generator.
• The owner is responsible for always keeping the unit in
safe working conditions.
• Always use approved parts when performing mainte-
nance and repairs. Make sure that replacement parts
meet or exceed the original parts’ specification.
• Only competent individuals, trained and authorized,
can install, operate, perform maintenance and repair.
• Isolate incoming and outgoing pressures to the gen-
erator, and depressurize the service or repair section
before performing any mechanical work, including
changing the filters.
• Vent the nitrogen generator’s exhaust gas outside or
to a large, well-ventilated room to avoid suffocation
due to lack of oxygen.
• Wear safety glasses if the cabinet door is open while
the machine is running.
• Use ear protection when the equipment is running.
NOTE: Always following local and site safety regula-
tions in conjunction with this manual. Correct use
of the nitrogen generator is important for personal
safety. Incorrect safety practices can cause damage
to the individual and equipment.
Follow safe working practices, OSHA, and local health
and safety regulation when maintaining the N2-Blast
®
FPS-900-RS.
Air Supply
The N2-Blast
®
FPS-900-RS includes a built-in air
compressor to supply gas to the nitrogen generator. It is
not for performing quick fills; a separate suitable air com -
pressor for should be used to fill the system.
Electrical Requirements
The N2-Blast
®
FPS-900-RS requires 120VAC / 50-
60hz / 1ph and draws < 8A. A 240VAC option is also avail-
able. It has a built-in 20A over-current protection device
and comes with a standard 3-prong US power cord for
the electrical connection (unless otherwise specified). It
comes with UL 508A ICP certification, and the electrical
schematics are available upon request.
Site Specifications
Unless designed otherwise, install in a nonhazard-
ous indoor location with temperatures between 40-100°F
(4°- 38°C). For ease of maintenance, troubleshooting,
and minimizing pressure drop, install the equipment in the
same area. Leave enough space around the generator
and other equipment for routine maintenance.
21.