EXTERNAL DEVICE CHARGING
To charge the external device, use the USB / micro USB cable included in the
kit. Connect the USB / micro USB cable to the Device and the external device.
Charging starts automatically and takes time to fully charge the external device
or until the energy in the Device runs out. After fully charged, disconnect the
device with an external device.
SAFETY
- Do not attempt to disassemble and do not take off the casing of the device.
- If the product leaks fluids, avoid contact with skin or eyes; if contact occurs,
immediately wash the affected area with water and consult a doctor.
- Do not leave packaging materials unattended, especially storage bags which are
a potentially dangerous toy for children (choking, swallowing, etc.)
- Use only original accessories and components supplied by the manufacturer.
- Make sure the current values of the device correspond to the current values
indicated on the Power Bank output.
-
The Device should not be directly exposed to sunlight and other heat sources.
- Ensure the Device does not come into contact with water, damp or steam to
avoid electrocution.
- The product is not a toy. Keep the device out of the reach of children.
- To prevent damage to the cord, do not let it be cut or hang from sharp edges
or corners.
- Do not run the Device if:
- the Device or cable is showing signs of damage,
- the Device is not working properly
In the above cases, contact the authorized service center of the manufacturer to
check the correctness of the Device.
the Device, the operating instructions of other external devices to which the
product is connected must be taken into consideration.
- The Device is intended for indoor use.
- During operation the Device produces heat. Ensure adequate ventilation and
do not cover the device during its use.
- Do not put anything into the ventilation slots and ports.
- For cleaning the appliance, use a dry cloth.
- The maximum load has been marked on the Device and the packaging, do
not load the device.
ENVIRONMENTAL PROTECTION
After using the equipment completely, all materials from which it was made can
be recovered in the form of new materials or energy. Repack the packaging and
handling instructions according to the local recycling scheme.
When unpacking the Equipment, separate the waste into a cardboard box and
blister, remembering about waste segregation.
By donating this type of waste in the right places, you contribute to the
protection of natural resources.
Such marking indicates that this equipment after its period of use can
not be placed together with other household waste. The User is obliged
to hand over the Equipment leading collection of waste electrical and
electronic equipment. The gatekeepers, including local collection
points, stores and municipal units, create an appropriate system for
putting this equipment into service. The proper handling of used
electrical and electronic equipment contributes to the avoidance of
harmful consequences for the health and the environment resulting
from the presence of hazardous components and improper storage and
processing of such equipment. The Device has limited some substances
that may have a negative impact on the environment during use and
after its use. The Device has limited some substances that may have a
negative impact on the environment during use and after its use.
The Device and accessories comply with the directives on the safety
of use, health protection and environmental protection to which the
declaration of conformity applies and therefore the Device was marked
with the CE mark and a declaration of conformity was issued to the
market surveillance authorities.
DEVICE COMPONENT INTRODUCTION
1. Slot output 5V/2.1A max
2. LED indicators
3. Slot output 5V/2.1A max
4. Micro USB slot Input
5. USB/Micro USB cable
6. POWER button
To charge The energy bank (hereinafter: the Device) is used to charge external
devices that are compatible with it.
Before using the Device, read the instruction manual completely and
thoroughly. It contains important information about the use of the Device and
is an integral part of it. Keep this manual for future reference.
The external device powered by the Device (energy bank) can be: phones and
tablets.
To determine if an external device is compatible with the Device, read and
can not be higher than the output current of the charger (OUTPUT).
BATTERY CHARGING
To charge the device, use a USB/micro USB cable. Connect the cable from the
side of a USB port into a power outlet with the maximum voltage up to 5 V DC.
A charger with a micro USB port or a USB port in a turned on PC may be a power
supply. Connect the cable from the side of micro USB port to the micro USB port
in the device IN 5V. LED is on when the device is charging. Disconnect the device
from a power supply when it is fully charged.
LED battery indicator using method: press the POWER button to turn on LED
Indicators. LED indicators will turn off automaticly after 5 seconds.
Power is left with the power bank, as below sheet:
EN
USER MANUAL
Thank you for choosing Reinston product.
LED
indicator
One
light on
Two
light on
Three
light on
Four
light on
Battery level
<25%
25–50%
50–75%
75–100%
5
IMPORTER, PRODUCER
SBS spa - Via Circonvallazione s/n
28010 Miasino (No) Italy
The Device was made in China
PHYSICAL PARAMETERS
2
1
4
6
3
Micro-USB Input: 5V - 2 A
Output: 5V - 2.1 A max
Li-Pol Battery: 20.000 mAh
REBB20000W - REBB20000K / EPB021, EPB022
