Rehabmart LASER HERO, Руководство пользователя

Страница: 5 / 9

LASER HERO USER MANUAL
3 INSTALLATION AND CONNECTION
3.1 PRE-INSTALLATION CHECK
Remove the parts of the device from the box and place it in a safe, stable position.
Check the accessories according to the packing list to ensure integrity.
3.2 CHARGING METHOD
When the Laser Hero is charging, the power
indicator is yellow; when fully charged, the power
indicator turns blue. The charging time reaches
85% for about 6 hours.
NOTICE:
• For first time use or if the device has not been used for a long time, it is recommended
to fully charge the battery before use.
• Prevent bumps and drops when the instrument is held or placed
• Use only our company approved power adapters and batteries that meet the safety
standards of IEC60601-1. Unauthorized power adapters can cause the device battery to explode
or damage the device.
• The device can be used while charging; This may extend the battery’s full charge time.
• If the power supply voltage is unstable during charging, and the light source cannot be started
normally, the charger can be unplugged from the device.
• The device generates a certain amount of heat when it is charged, which is a normal phenomenon
and does not affect the performance and service life of the device. However, if the battery is
abnormally overheated, stop charging immediately.
• If the battery does not charge properly, please contact our customer service department.
• Disconnect the device from the charger after fully charging. Unplug the charger from the device
and unplug it from the power outlet.
• To save power, unplug the power adapter when not in use. When charging, the charger should be
in full contact with the outlet.
• The instrument should be installed and operated to ensure normal working environment, power
supply, and electromagnetic compatibility requirements. Refer to the data provided in
Appendix F to ensure a normal working environment.
3.3 INSTALLING THE INNER LINER
Paste the inner liner of the appropriate
thickness according to the size of the head.
4 OPERATION OF INSTRUMENT
4.1 PREPARATION BEFORE TREATMENT
Before treatment, clean the scalp and dry the hair. .
4.2 OPERATION OF LASER HERO
4.2.1 Instrument operation method
1) Effective irradiation zone
of the light source is shown
in the FIGURE 4-1.
2) According to the patient’s head
circumference, a suitable inner liner is
pasted on the inner side of the hair loss
therapy helmet (adjustable sizing).
3) Press and hold the “ ” button until lighting and the working mode prompt voice will
say
“Welcome”.
4) Press the “ ” button to select the treatment time (25 min, 30 min, 35 min, unit: minutes).
If not, the default treatment time is chosen. Press the “ ” button to flash and the voice prompt
“Treatment begins, please wear the helmet” will be sent out. Once the helmet is placed on your
head, the laser is turned on and the treatment begins. The prompt voice “The remaining treatment
time is 5 minutes” will sent out when there is 5 minutes treatment time remaining. When the
treatment ends, the prompt voice “Treatment has ended,thank you for using” will be sent out.
5) It is recommended to irradiate every two days.
6) In the course of treatment, if pressing the “ ” button again, the treatment will be stopped
and the “ ” button will stop flashing.
7) In the course of treatment, if the hair loss therapy helmet is removed, the irradiation will be
paused and the prompt voice “Treatment stopped,the helmet will be turned off in 3 minutes”
will be sent out. If the hair loss therapy helmet is re-worn within 3 minutes, the irradiation will
continue.with a prompt voice“Continue for treatment”.If the hair loss therapy helmet is not put
on within 3 minutes, the instrument will be automatically shut down.
8) Press and hold the “ ” button, voice on or off can be chosen. When the “ ” button is
flickering, the instrument is under the waiting for treatment or working state. At this time,the “ ”
button cannot be operated.
9) Press and hold the “ ” button, indicator lights shut off, and power ends.
08 | 09