Regency PG121-LPG Скачать руководство пользователя страница 22

Страница: 22 / 44

Regency PG121/PG131 Zero Clearance Room Sealed Gas Fireplace

INSTALLATION

Conversion Kit for NG to LPG Model #736-969

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !!

Conversion Kit 736-969 Contains:

Qty. Part # Description

1 904-641 Burner Orifice #50

1 908-528 Red "LPG" label

2 918-590 Label "Converted to LPG"

1 918-335 Instruction Sheet

1 910-920 LPG Pilot Orifice

Shut off the gas supply and unplug the

power cord.

Remove louvers and trim.

Carefully remove the glass, logs and lava

rock.

Remove the grate by lifting straight up.

Remove the side brick panels (if installed).

The

brick panel is very fragile - handle

with care.

11)

Remove burner orifice with a 1/2" spanner

and discard. Use another spanner to hold on

to the elbow behind the orifice.

Control Box

Cover

Antenna

12)

Reinstall new burner orifice LPG stamped

#50 and tighten.

13)

Check the areation for the LPG burner and

install the burner, grate and logs.

14)

Remove the front cover by undoing the 2

screws.

Remove pilot inner box by removing the 2

screws.

Lift the pilot assembly and remove the pilot

tube from the pilot holder using a 11mm

wrench.

Remove the NG pilot orifice and replace it

with the LPG orifice.

Diagram 1: Remove the left and right

screws and then slide the burner assembly

away from the orifice and lift out.

Remove the burner assembly by removing

the 4 Phillips head screws and then slide

the burner assembly away from the orifice

and lift out.

Install the pilot tube to the pilot assembly.

10)

Place the pilot assembly and pilot inner box

over the pilot extrusion tube and secure it

with 2 screws.

Pilot

Assembly

Pilot

Orifice

Pilot

Tube

Pilot

Extrusion

Tube

15)

Stick the conversion label "This unit has

been converted to LPG" over top of the

serial number decal.

16)

Replace the yellow "NG" label with the red

"LPG" label.

17)

Unplug the 5 pin Molex Connector and

carefully pull out the control box.

NOTE: The control box is held in place with

velcro.

Front Cover

18)

Remove the control box cover by undoing

the 3 screws. Maneuver through antenna.

5 Pin Molex

Connector

Содержание PG121-LPG












































Результаты поиска

Содержание PG121-LPG

Отзывы:

Похожие инструкции для PG121-LPG

Бренды по названию

Популярные бренды

Regency PG121-LPG, Владельцы и установка

Результаты поиска

Содержание PG121-LPG

Отзывы:

Похожие инструкции для PG121-LPG

Бренды по названию

Популярные бренды