background image

B41XTCE Gas Fireplace

Model

B41XTCE-NG11

B41XTCE-LP11

Fuel Type

Natural Gas

Propane

Minimum Supply Pressure

5” W.C./C.E. (1.25 kPa)

11” W.C./C.E. (2.74 kPa)

Manifold Pressure - High

3.5” W.C./C.E. (0.87 kPa)

10” W.C./C.E. (2.49 kPa)

Manifold Pressure - Low

1.6” W.C./C.E. (0.40 kPa)

6.4” W.C./C.E. (1.60 kPa)

Orifice Size -

Altitude 0-4500 ft.

#30 DMS 

#49 DMS 

Minimum Input  

Altitude 0-4500 ft. (0-1372m)

30,000 BTU/h  

(8.79 kW)

29,500 BTU/h 

(8.65 kW) 

Maximum Input 

Altitude 0-4500 ft. (0-1372m)

42,500 BTU/h 

(12.45 kW)

37,500 BTU/h 

(10.99 kW)

CSA P.4.1

68.15%

68.35%

Q

P

U V

T

Opening for gas

connection

11" (279mm)

dia. Hole through

wall Vent.

Non-Combustible

Header

(steel stud) on edge

Drywall

(or other

facing)

W

Non-Combustible Facing

S

S

R

Non-combustible

Header

(steel stud

on edge)

M

N

L

O

** Important:  Framing height requires consideration of the hearth depth.  

   Dimension N = N + the thickness of the installed hearth.

Approved Venting Systems

Flex Vent Systems:

FPI AstroCap™ Flex Vent

Rigid Pipe Vent Systems:

Simpson Direct Vent Pro®
Selkirk Direct-Temp™
Metal-Fab® Sure Seal
ICC Excel Direct Vent

28-

1/2"

38-3/8"

22-1

1/16"

46-11/16"

25-9/16"

16-7/16"

32-5/8"

38-1/4"

36-3/8"

26-3/16"

3-1/4"

49-

1/4

"

11-

5/8"

7-5/16"

1-9/16"

1-1/2"

35"

44-1/4"

3-5

/8"

29-

1/8"

23-7/16"

38-7/16"

[1185mm]

[974mm]

46-11/16"

[1185mm]

[976mm]

[889mm]

[7

38m

m]

[92

mm

]

[594mm]

[649mm

]

[664mm]

[1

251

mm

]

[38mm]

[1

123mm]

[417mm]

[82

9mm

]

[185mm]

[294mm]

[7

24m

m]

[39

m

m]

[92

3m

m]

[97

1mm]

[576mm

]

Framing 

Dimensions

Description

B41XTCE

M

Framing Width

47-1/4"(1200mm)

N

Framing Height

49-1/2" (1257mm)

O (Rear Vent)

Framing Depth - Rear Vent

26-1/2" (673mm) 

O  (Top Vent)

Framing Depth - Top Vent

25-7/8" (657mm) 

P  

Corner Facing Wall Width

65-1/4" (1657mm)

Q  

Corner Facing Wall Width

91-11/16" (2329mm)

R (Rear Vent)

Framed Chase Ceiling - Rear

49-1/2" (1257mm)

R (Top Vent)

Framed Chase Ceiling - Top

54-1/2" (1384mm)

S  (Rear Vent)

Vent Centerline Height - Rear

28-1/2" (724mm)

S  (Top Vent) 

Vent Centerline Height - Top

47-1/2" (1207mm) Rigid / Flex

T

Gas Connection Height

1-1/2" (38mm)

U

Gas Connection Inset

5" (127mm)

V

Gas Connection Width

3-1/4" (82mm)

W

Non-Combustible Top Height

6" (152mm)

Gas Fireplaces

Содержание B41XTCE-NG11







Отзывы: