Regency B36XT Bellavista Скачать руководство пользователя страница 57

Страница: 57 / 68

Regency Bellavista™ B36XT Gas Fireplace

INSTALLATION

Finishing

Trim Top

Finishing

Trim Side

NOTE:

Install the Finishing Trim prior to installing the Flush Louvers.

Install the Finishing Trim sides as shown in the diagram; line up the holes in the
side trim with the holes in the fi rebox side.

Secure with 2 screws per side.

Loosen the 2 screws in the top inside edge of the fi rebox.

Slide the Finishing Trim Top over the Side Trim pieces and fi t the

bottom bracket slots over the screws. Tighten the 2 screws to
secure in place.

Finishing Trim

Edge of Unit

B41XT

B36XT

43-3/8"

40-1/2"

37-5/8"

35-3/4"

OPTIONAL FINISHING TRIM INSTALLATION

FLUSH LOUVERS AND FLUSH PANEL INSTALLATION

To install the top and bottom louvers or fl ush panels:

1) Locate the tabs on louvers/fl ush panels.

2) Line up the tabs on louvers/fl ush panels with the brackets on the
unit.

3) Hook the tabs up over the brackets to attach.

Tabs on Louver/Flush Panel

Bracket on unit for upper

Louver/Flush Panel

Bracket on unit for lower

Louver/Flush Panel

Installation of upper

Louver/Flush Panel

Installation of lower

Louver/Flush Panel

Содержание B36XT Bellavista





































































Результаты поиска

Содержание B36XT Bellavista

Отзывы:

Похожие инструкции для B36XT Bellavista

Бренды по названию

Популярные бренды

Regency B36XT Bellavista, Инструкция для владельца и по установке

Результаты поиска

Содержание B36XT Bellavista

Отзывы:

Похожие инструкции для B36XT Bellavista

Бренды по названию

Популярные бренды