Regency 600PHSHEATER Скачать руководство пользователя страница 8

8

LOCATING THE NEW WATER HEATER

IMPORTANT SAFETY INSTRUCTIONS

Facts To Consider About The Location

Carefully choose an indoor location for the new water heater, 
because the placement is very important consideration for 
the safety of the occupants in the building and for the most 
economical use of the appliance.
Whether replacing an old water heater or putting the water 
heater in a new location, the following critical points must be 
observed:

1.  Select a location as close as practical or centralized to the 

point of use. The water heater should be located in an area 

not subject to freezing temperatures.

2.  Selected location must provides adequate clearances for 

removing the front cover in order to service parts such as the 

thermostat, element, temperature sensor, anode, and high 

limit reset. Adequate clearance for servicing this appliance 

should be considered before installation, such as operating 

the relief valve, etc.

3.  The water heater should be located so it is not subject to 

physical damage by moving vehicles or area flooding.

4.  The selected wall or cabinet must be capable of supporting 

at least two times the weight of the water heater when filled 

with water (7 7Ibs).

5.  The water heater must be installed in a vertical position with 

water inlet and outlet connections facing upwards and easily 

accessible.

Installation of the water heater must be accomplished in such a 
manner that if the tank or any connections should leak, the flow 
will not cause damage to the structure. For this reason, it is not 
advisable to install the water heater in an attic or upper floor.
When such locations cannot be avoided, a suitable drain pan 
should be installed under the water heater. Drain pans are 

available from your local plumbing contractor. Such a drain pan 
must have a minimum length and width of at least 2 inches (51 
mm) greater than the water heater dimensions and must be piped 
to an adequate drain.
Water heater life depends upon water quality, water pressure, 
water usage, water temperature, and the environment in which 
the water heater is installed. Water heaters are sometimes 
installed in locations where leakage may result in property 
damage, even with the use of a drain pan piped to a drain.
However, unanticipated damage can be reduced or prevented 
by a leak detector or water shut-off device used in conjunction 
with a piped drain pan. These devices are available from some 
plumbing supply wholesalers and retailers, and detect and react 
to leakage in various ways:

• 

Sensors mounted in the drain pan that trigger an alarm 

or turn off the incoming water to the water heater when 

leakage is detected.

• 

Sensors mounted in the drain pan that turn off the water 

supply to the entire home when water is detected in the 

drain pan.

• 

Water supply shut-off devices that activate based on the 

water pressure differential between the cold water and hot 
water pipes connected to the water heater.

INSULATION BLANKETS

Insulation blankets are available to the general public for external 
use on electric water heaters but are not necessary with this 
product. The purpose of an insulation blanket is to reduce the 
standby heat loss encountered with storage tank heaters.
Should you choose to apply an insulation blanket to this heater, 
you should follow these instructions below. Failure to follow 
these instructions can result in fire, serious personal injury, or 
death.
Do not cover the temperature and pressure relief (T&P) valve 
with an insulation blanket.
Do not cover the instruction manual. Keep it on the side of the 
water heater or nearby for future reference.
Do obtain new warning and instruction labels for placement on 
the blanket directly over the existing labels.

1.  READ ALL INSTRUCTIONS BEFORE USING THIS WATER 

HEATER.

2.  This water heater mush be grounded. Connect only 

to properly grounded outlet. See GROUNDING 

INSTRUCTIONS found in the WIRING section of  

this manual.

3.  Install or locate this water heart only in accordance with 

theprovided installation instructions.

4.  Use this water heater for its intended use as described in this 

manual.

5.  Do not use an extension cord set with this water heater. 

If no receptacle is available adjacent to the water heater, 

contact a qualified electrician to have one properly installed.

6.  As with any appliance, close supervision is necessary when 

used by children.

7.  Do not operate this water heater if it has a damaged cord or 

plug, if it is not working properly, or if it has been damaged 

or dropped.

8.  This water heater should be serviced only by qualified 

service personnel. Contact nearest authorized service facility     

for examination, repair, or adjustment.

 CAUTION

Property Damage Hazard

• 

All water heater eventually leak

• 

Do not install without adequate drainage

 DANGER

Fire Hazard/Electrical Shock Hazard 

When using electrical appliances, basic safety 
precautions to reduce the risk of fire, electric 
shock, or injury to persons should be followed. 

Содержание 600PHSHEATER






















Отзывы: