manualshive.com logo in svg

Regency Fireplace Products Plateau PTO30, Инструкция для владельца и по установке, Страница: 21 / 52

Поделиться
Скачать
Regency Fireplace Products Plateau PTO30 Скачать руководство пользователя страница 21

 

Regency Plateau

®

 PTO30-11 Outdoor Gas Fireplace

e  |     

21

21

| 

installation

FINISHING

Side nailing strips are adjustable for material from a minimum of 1/2" thick 
up to a maximum of 2-3/8" thick.

The finishing materials cannot extend beyond the height of the burner.

Optional finishing trim is supplied with the PTO30 - place finishing trim on unit between unit and finishing material.
Note: If installing a PTO60 the optional trim on the PTO30 cannot be used and should be discarded. An optional trim (part number 377-957) can be pur-
chased for the PTO60.

Side nailing strips are adjustable in 1/4" or 1/8" increments.  Each hole on 
the inside line is 1/8", each hole on the outside line is 1/4".
Determine the thickness of the finishing material before adjusting the nailing 
strips.

OPTIONAL FINISHING TRIM

1/2"

1/4" Increments        

1/8" Increments        

2-3/8"

Nailing strip

FINISHING MATERIALS: 

This burner is designed to be finished with non-combustible materials (ie. 
tile, granite, marble, brick, etc.) with a minimum thickness of 1/2" to a maxi-
mum thickness of 2-3/8".

Burner Opening Size
PTO30 36-7/16" x 8-1/4"
PTO60 66-7/16" x 8-1/4"

Min. 1/2"
Max. 2-3/8"

Important Note: 

Two (2) ventilation grills, (PTO30), Four (4) ventilation 

grills (PTO60) are required for all enclosures. 
This is to alleviate moisture and allow for air to circulate. 
Minimum recommended size : 20" sq (508 mm ²) each.

Содержание Plateau PTO30





















































Отзывы:

Нет отзывов