Regency Fireplace Products P48 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 44

background image

Regency P48 Zero Clearance Direct Vent Gas Fireplace

30

INSTALLATION

WIRING DIAGRAM

CAUTION: Label all wires
prior to disconnection
when servicing controls.
Wiring errors can cause
improper and dangerous
operation.

No electrical power supply is required for the
gas control to operate. 120 Volt AC power is
needed for the fan switch and blower. The fan
can be hard wired if desired. A terminal block
is provided on the left hand side of the unit. A
three wire power cord can also be used and
plugged into a suitable receptacle.

(Do not cut the ground terminal off under
any circumstances.)

NOTE: Even if the fan is not purchased with the
unit, it is still a good idea to hardwire the terminal
block in case the fan is installed at a later date.

** However DO NOT leave this connection
live until the fan is installed.**

Caution: Ensure that the wires do
not touch any hot surfaces and are
away from sharp edges.

«
...
28
29
30
31
32
...
»

Содержание P48













































Отзывы:

Нет отзывов

Похожие инструкции для P48

Бренд: Valor Страницы: 41

Бренд: EdilKamin Страницы: 28

ECO-prestige 75

Бренд: KAL-FIRE Страницы: 184

Бренд: Dimplex Страницы: 12

Бренд: Valcourt Страницы: 12

Cosi square glass set M

Бренд: Gimeg Страницы: 2

Бренд: wiking Страницы: 4

Caress Slimeline SC FNVC**SN

Бренд: Flavel Страницы: 12

Integra SuperSlim Slide Control

Бренд: Cast Tec Страницы: 16

Бренд: Napoleon Страницы: 136

Wellington Surround

Бренд: Valor Fires Страницы: 8

Бренд: Clifton Страницы: 50

Бренд: Empire Comfort Systems Страницы: 4

OUTDOOR LIVING REDEFINED OUTDOOR FIREPIT

Бренд: California Outdoor Concepts Страницы: 16

AUSTIN-65G-LP-DELUXE

Бренд: Sierra Flame Страницы: 54

Бренд: Extraflame Страницы: 84

Бренд: baltur Страницы: 72

Бренд: Heat & Glo Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды