Regency
®
P33-4 Zero Clearance Direct Vent Gas Fireplace
6
INSTALLATION
IMPORTANT MESSAGE
SAVE THESE
INSTRUCTIONS
The P33-NG4 or P33-LP4 Direct Vent Fireplace
must be installed in accordance with these
instructions. Carefully read all the instructions
in this manual fi rst. Consult the "authority
having jurisdiction" to determine the need for
a permit prior to starting the installation. It is
the responsibility of the installer to ensure
this fi replace is installed in compliance with
manufacturer's instructions and all applicable
codes.
BEFORE YOU START
Safe installation and operation of this appliance
requires common sense, however, we are
required by the Canadian Safety Standards
and ANSI Standards to make you aware of
the following:
GENERAL SAFETY
INFORMATION
1)
The appliance installation must conform with
local codes or, in the absence of local codes,
with the current Canadian or National
Gas Codes, CAN1-B149 or ANSI Z223.1
Installation Codes.
2)
The appliance when installed, must be
electrically grounded in accordance with
local codes, or in the absence of local codes
with the current National Electrical Code,
ANSI/NFPA 70 or CSA C22.1 Canadian
Electrical Code.
3)
See general construction and assembly
instructions. The appliance and vent should
be enclosed.
4)
This appliance must be connected to the
specifi ed vent and termination cap to the
outside of the building envelope. Never vent
to another room or inside a building. Make
sure that the vent is fi tted as per Venting
instructions.
5)
Inspect the venting system annually for
blockage and any signs of deterioration.
6)
Venting terminals shall not be recessed into a
wall or siding.
7)
Any safety glass removed for servicing
must be replaced prior to operating the
appliance.
8)
To prevent injury, do not allow anyone who
is unfamiliar with the operation to use the
fi replace.
9)
Wear gloves and safety glasses for protection
while doing required maintenance.
10)
Be aware of electrical wiring locations in
walls and ceilings when cutting holes for
termination.
11)
Under no circumstances should this
appliance be modifi ed. Parts that have to be
removed for servicing should be replaced
prior to operating this appliance.
12)
Installation and any repairs to this appliance
should be done by a qualifi ed service
person. A professional service person
should be called to inspect this appliance
annually. Make it a practice to have all of
your gas appliances checked annually.
13)
Do not slam shut or strike the glass door.
14)
Under no circumstances should any solid
fuels (wood, paper, cardboard, coal, etc.)
be used in this appliance.
15)
The appliance area must be kept clear and
free of combustible materials, (gases and
other fl ammable vapours and liquids).
MANUFACTURED
MOBILE HOME
ADDITIONAL
REQUIREMENTS
1)
Ensure that structural members are not
cut or weakened during installation.
2)
Ensure proper grounding using the #8
ground lug provided. Refer to "Wiring
Diagram" Section.
INSTALLATION AND REPAIR
S H O U L D B E D O N E B Y A
QUALIFIED SERVICE PERSON.
THE APPLIANCE SHOULD BE
I N S P E C T E D B E F O R E U S E
AND AT LEAST ANNUALLY
B Y A P R O F E S S I O N A L
S E R V I C E P E R S O N . M O R E
FREQUENT CLEANING MAY BE
REQUIRED DUE TO EXCESSIVE
L I N T F R O M C A R P E T I N G ,
B E D D I N G M AT E R I A L , E T C .
I T I S I M P E R AT I V E T H AT
CONTROL COMPARTMENTS,
BURNERS AND CIRCULATING
A I R P A S S A G E W AY S O F
T H E A P P L I A N C E B E K E P T
CLEAN.
YOUNG CHILDREN SHOULD BE
CAREFULLY SUPERVISED WHEN
THEY ARE IN THE SAME ROOM
AS THE APPLIANCE.
Emissions from burning wood or gas could
contain chemicals known to the State of
California to cause cancer, birth defects
or other reproductive harm.
DUE TO HIGH TEMPERATURES,
THE APPLIANCE SHOULD BE
LOCATED OUT OF TRAFFIC AND
AWAY FROM FURNITURE AND
DRAPERIES.
WARNING: FAILURE TO INSTALL
THIS APPLIANCE CORRECTLY
WILL VOID YOUR WARRANTY
AND MAY CAUSE A SERIOUS
HOUSE FIRE.
C H I L D R E N A N D A D U LT S
SHOULD BE ALERTED TO THE
HAZARDS OF HIGH SURFACE
TEMPERATURES, ESPECIALLY
T H E F I R E P L A C E G L A S S ,
AND SHOULD STAY AWAY TO
AVOID BURNS OR CLOTHING
IGNITION.
C L O T H I N G O R O T H E R
FLAMMABLE MATERIAL SHOULD
NOT BE PLACED ON OR NEAR
THE APPLIANCE.
